Our RU-vid channel will keep you updated on the latest lighting news, technological advances, as well as providing simple installation guides and tips for the fellow DIY enthusiast. The company itself Downlights Direct, is a lighting specialist in downlights, low energy lighting aswell as commercial lighting. The company is based in Greater Manchester and we hold huge stocks of downlights, LED lamps and LED strip.
Wifi, remote and an app? Surely it's one or, not both? All I want to know if you need a special "socket" or if the lightbulb itself has controller in it and is self-sufficient
Since, the lumens have doubled at the same power, and the cost has dropped +4x - the only negative is the newer ones last best case half as long as the older gen LEDs
Can we connect a 3 meter or 5 meter led strip (12 volts, 20 watt per meter , 240 led per meter ) to a 12 volt car battery directly without drivers , assume passive cooling is provided for led strip.
I’m looking to connect 8x 1m led strips which are at 400mA, 4.8W/m and 12V, I’m trying to connect these to a switch in the room what driver should I use?
Kitchen fitters put led strips in our kitchen, and after 6 months, the lights went dim. Fitter has us used a 12v DC 30w LED Converter 2.5A, 100-240v AC. Is this led transformer the correct specification do you think? It's a small to medium-sized kitchen and leds just run under wall units and inside a glass cupboard.
I am replacing the led driver of my ceiling light, can i use output regulated current of 750mA where the old one is only 660mA? The rest of the spec are the same.
I want to replace a wall light with 5 LED strip lights (for a shelving unit). Do I just connect a driver to the existing wall light switch and the LED strips? I don't have a power socket nearby.
Teco’s Classic GU10 dimmable spotlights are a perfect fit for spot lighting and deliver warm halogen-like light. They are compatible with most existing fixtures are designed as a retrofit replacement for halogen or incandescent spots. LEDlamps deliver huge energy savings and minimize maintenance cost. They also has excellent compatibility to various dimmers provided by different manufacturers. ◆ Real replacement of 75W Halogen reflector ◆ Delivers 575lm light output with merely 7.5W power consumpion ◆ Four different beam angles: 10° 24° 36° and 60° ◆ Ra>90 ◆ Compatible with both leading edge and trailing edge dimmers ◆ L70 life up to 25000hrs, 3 years limited warranty
I have what I believe to be a full spectrum led grow light. The main issue is that it's a cheaper setup and the LED drivers (4) are unmarked and two of the 4 are not working. How can I test them and how can I determine which drivers would be needed to replace the non working ones? I would greatly appreciate any helpful information! Thank you in advance!
I have just replaced a 50W halogen bulb with a 5W (35W equivalent) MR16 LED bulb. I have also replaced the driver with an Aurora AU-LED 16T constant voltage driver 12V 1-16W. The bulb strobes like a disco . Can anyone tell me what I have got wrong.
Hi I have a question. I have 9 led downlights of 24w each with its driver. I wanted to know if I can replace the nine drivers that each one comes with and power them all with a single 300W driver.
Hi, it depends what output of your nine drivers, could you take them out and check, then I would know what parameter of the driver you can use to driver power 9 led downlights.
@@wenyingjiang504 Thanks for your interest in helping :) The driver specifications for each downlight say: LED DRIVER, MODEL: (19-24) X1W, PRI: AC85-265V 50 / 60Hz, SEC: 280mA ± 5%, OUTPUT LOAD: DC57-96V. Do you think this model HLG-320H-C3500. It could replace the nine led drivers with the features mentioned above. And only use this LED DRIVER with higher capacity to power the nine downlights?
I was planning to fire up 50pcs of 3v diodes. Since I dont have a driver I used CP charger with an output of 5v. I used a converter to stepped the volts down to 3v.
i have an led light for my aquarium original driver broke, but it was using a 3 pin meaning 3 wires for the dual light switch blue and white, do you know what type of driver I need for 3 wire of my light. any info would be much apreciated.
The light just arrived Tuesday installed it imgs.love/SRetrofitLight?Д2 that afternoon very easy and simple to set up made the adjustments and seems to be doing what I wanted to do. That is to light up my garage when I go through the doorway.
As a newbie to downlight stuff i was hoping this video would explain me how and where and when to hook the earth wire on our downlight that doesn't provide the earth wire socket out of the box.