@@medievalpilgrim Thanks. I may make it easier than it looks. Lots of time and frustration happens off camera :D but it will be worth it !

@@CMFotoPeak Im trying do the same :) One big video how i turn it from the scrap to the final look so i know what pain is that. Keep it up i cant wait for part 2 !

There is a charger you can just plug into the same port the tethered cable also plug into.

Yes, but was not easy to remove, it's all spot welded, that's why I ended up just cutting most of it away in the end. :)

Its a QYSEA FIFISH V6s

What I was expecting lmao

I got the 100meter line for it but have never been used fully, as we dont have waters that deep here :)

Would love to get down about 80 to 100 feet in some deep Canadian Lakes.@@CMFotoPeak

Hi, the welder was something I borrowed that could do aluminum (Sigma Galaxy 400). It did an ok job, but definitely hard to do right on thin sheets. Unfortunately I don't remember what settings was used. I tried welding aluminium with TIC but that was not a success either.

Tell me about it, I test fitted 1 window, which took several sessions over 3 days to get right :')

@@CMFotoPeak I gave up and got a friend to do mine in the end (after marring the side panels a dozen times!) - The small ones at the back are easy... a bit of soapy water does the trick 👍

Hi. Yes at first, and shortly corrected the error. I mentioned this in the commentary track :)

Hej Christoffer. Tak, jeg prøver efter bedste evne. I gang med at male og samle den igen. Er bare bagud med videoer :) . Kommer fra omkring Fakse på sjælland. Regner med at tage til diverse træf når den engang er færdig såsom Gavnø og kørtilkøge. Tror godt jeg har set dig på FB hvis du er den samme, da du muligvis havde noget LR relaterede ting til salg ;) mvh Casper

I think it's the original, as i didn't change it. it says 39184 and 1381A on it. I haven't actually tested if it works yet ;D

Noted about the cylinders as it was a pain to install. Not sure which connectors you're referring too ?

@@CMFotoPeak I mean the Brakeline nipples. The latest threads are M10x1mm. Some are 3/16"?

Hi, Looking back at it, the bulkhead was indeed a pain to fix. New bulkhead here costs a fortune so the repair was the way at the time. Very soon final paint and time for reassemble of everything.

Hej Jacob. Jeg kan godt anbefale Fifish v6s. Tror dog der er kommet en ny version som hedder noget med Fifish v-Evo, som vidst kan det samme. Jeg gav lige godt et sted mellem 15.000-20.000 da den kom ud, hvilket nu også er en sum penge. Jeg har ikke liget fået brugt min på det seneste grundet andre projekter. Du skal dog regne med at sådan som søer og andre stillestående vandhuler kan det være fuldstændig umuligt at se noget pga. mudder/grønt vand. Det kan også være gældende om sommeren nå vi plages af alger i vandet ved havne. Tak for lige at gøre opmærksom på link ikke dur længere :)

Tak for dit svar - jeg vil overveje det nøje. Jeg kiggede online og bemærkede godt den høje pris, så det er et dyrt legetøj @@CMFotoPeak

Hi, honestly I don't know. some say the quality was better in the 'Good old days. But harder to find and but everything I bought so far have been new, and it have not necessarily been genuine OEM.

First time was in march, and this footage is in oktober 2022. I have been back serveral times here, but it's always just that nasty layer of sludge now :(

@CMFotoPeak God damn, the lakes around me are either completely green water or this slimey ground or even worse both at the same time 🤣

I think it really depends on the weather. If sunny and warm, then the water is full of algae and you can't see anything. I never had good time with lakes, as they are always full of algae here. :)

@@CMFotoPeak same 😐

I think it was more a way to just reach inside the toolbox , as the driverseat was replaced with a suspension seat that covered the whole access hatch. 🤣

Oh yes, those rubber pads was quite difficult to deal with :D

I can't quite recall if that was the case with the gearbox, but always annoying working with a car that use the nuts/bolts that you don't usally use in your own country 🤣

Floor, body mounting, and top hats was all cut and made by a local shop which made it a whole lot cheaper than the ones that is pre-bend and sold. But must admit whole project is getting a bit more expensive than what I expected :'D

Wrote to you on your instagram :)