I just used 2 ZipTies to hold it open. It takes a little "finagling" and a lot of patience... but it works.

I've done it,sounds throaty,no power loss to speak of

did you end up having to use that bag bracket it came with? i got the same pipe and mine didnt come with it

🔥 I’m interested in swapping my tbr for the sawikie for my fxbb but can’t decide on the shorti or the mid length I did here the mid Length makes good power also brother what riser set up your running should do a video on them ?!

Very helpful thank you sir!

Hey whats that passenger seat bruh!??? you have paired it with the stock seat! let me know!!!

I did the same thing it's too hollow for my liking but I did install DK Customes thunder tourqe inserts and gave back a bit of low end tourqe

Can you remove the flapper like completely if you put a full exhaust?

I’ve recently developed the chirping noise at start up in my Suburban. I’m active in an online group so I knew what it was. After seeing so many videos about hose clamps, I stumbled across yours and man, you are a lifesaver. It took me 2 minutes and the chirp is gone. Plus, as an added bonus, cold starts and acceleration sound way better. Now, it’s time for a Flowmaster. Thanks man!

So when you look inside the pipe and couldn't see thru what you're looking at is a perforated ceramic puck. I removed mine and holy loud!

I cut mine right off when I swapped mufflers, sounds beautiful in or out of AFM mode. Yeah there’s a rumbly drone on the freeway but I like it.

Good video brother! By chance, did they make contact with your windshield when turning your forks? I want to buy these, but I’m not sure if they make contact with the windshield or not. Thanks brother. God bless!!

Turn it to the front of the truck basically

I’m bout to do this at least until I have the money for the exhaust I want on my street bob

What’s with the springs?

Can you put the end caps back on or did you just leave it open?

Thanks for the video dude!!

Thank you, cool throaty sound for free!

Thanks ❤

I did this but I’m honestly not sure I turned it the right way. It is locked when I try to twist one way and twisted a good amount the other way. Is it possible for it to get stuck closed?

Nice does that have the cat in the collector ? thank you

Looks great! I want the mid length but all the pictures I see it has an upsweep which I don’t care for. What do you plan on doing for a tune?

I’m in the same situation you were at the beginning, probably 6 months til I can get a 2into1. Would you still recommend removing the baffles in the meantime? My washer sounds better than this stock set up 😂

remove the packing. reinstall baffles or install torque cones................

Looks sick, sounds sicker🤘🏻

Chingon

That IS the cat converter.

I doing it to my Low Rider st. I stay in Encinitas

Good on explaining the situation.

You left Oring on?

What seat did you go with?

Hey, your rear saddle bag crash guard bars, what brand are they?

I've read it not so much back pressure thats the issue, its more of a reversion problem that robs performance.

hot dog,,gonna do mine. thx brah. big island

EPA strikes again, unelected bureaucrats deciding what’s best

Awesome video

Not sure how the hell you was able to push that spring in and twist it to that other section, but I tried for ever with no luck. I ended up holding the flapper open and putting a small hose clamp around it and tightened it down. Doesn't move at all.

Opening it is just for sound adjustment? Or is there performance enhancing behind it as well

Can just remove mine or will i get codeson dashboard

On my truck there was 9hp difference when opened on dyno if you have it tuned for v8

I cut mine off when I did a muffler delete

Thank you!!! Just did mine today!! Stock exhaust, 2022 5.3, covered resonator screens, I’ll drive it a bit and if we need more than we’ll just have to replace the muffler!!!😁😁😁

Thank you for your time man!!! Been wondering if there was a simple way to do exactly this. Excellent job!!

Dopeness, me likey..

So does it make the truck sound better onces u open it ?

Cool video.

Thanks, mine was stuck closed

Thank you dude.. I was looking into my throttle cable, tensioners, etc trying to figure out what the f the chirping sound was.. Mine is on start up and when accelerating. This is exactly what it is. Gonna order a AFM disabler and crack the flapper valve open. Much appreciated. Saved me some sleep on this one lol

Thanks, did this yesterday!

Thanks