Happy holidays mate.. We set the limit low but the unit is fixed at 18 degrees Celsius as the lowest... It's too hot for us, do you know how to solve this ?
Thanks I need to check it. I just got error Code H 85 on my AC display. It turns on a profile at 7pm and it had not turned it on this time. I thought maybe someone at home turned it off as the weather has become very cold all of a sudden. The display was off. Then It started flashing. H and then 85. And repeating. it. I turned on the AC and it turned on. It was too cold so I did not turn it on to check if its working I thought let me google the codes. There is no H 85 code anywhere. Infact your video is the only one that mentions errors codes of RAC. Thanks for the video
Not an intuitive system at all. Thanks for making this video. Panasonic must have a bunch of kids writing the programs for their air con controls. I have a £16 eBay thermostat with weekly programs running my underfloor heating and even the chinglish manual is easier to understand and program than a Panasonic. What is going on??
@@dorinbazavan5683 Hi, yes, it was the PCB. It had a manufacturing defect (bad serie of PCBs) as soon as weather temperatures were higher, the PCB went faulty (outdoor unit was in direct sunlight, after a while there was a short circuit, that explains the H97 fault). Panasonic replaced it under warranty. My second outdoor unit had the same issue last week, so that one has a bad PCB as well.
Great video, so the question is where do I find it to rip it out! :) Got a tip since I get less heating this might be the problem since it maybe cannot retain high voltage over time with a broken coil. Heats a bit and then drops down and cannot deliver much heat anymore. Helps somewhat to put it in cool then back to heat. No error codes.
Is this setting the reason why my heating won't work today? I'm cold sitting inside my house despite the outside temperature showing 29C. However, I can't get the heating to work, but the hot water will heat up. I've tried various things like deleting and resetting all the timer settings, increasing the heat temperature to 30C etc., but nothing happens. Water pressure is all ok. The heating was working fine this morning when the outside temperature was cooler. Will this outside temperature have been set on my heat pump when they installed it?
Hi, thanks for a informative video! I have a multisplit system (Panasonic) and when I use one indoor unit for heating and the other indoor unit is off gas is still circulated to the unit that is off. I can feel warm temperature on the top of it and when the system de-ices I hear it bubbling also in the indoor unit that is off. Should´n the expansion valve prevent heated gas to circulate to the indoor unit set to off? This all get frustrating when the active indoor unit is not producing enough heat. Another problem is that when booth indoor units are on but with different temperature settings, say 22 and 17 degrees (one is bedroom) then the bedroom heating does not stay on the 17 degrees but increases up to 22 and sometomes above. (bedroom is a smaller room than the livingroom).
I have seen the video and it has helped me a lot to configure the weekly ignition of the unit, but I set the temperature and I want it to come out as heat, but the mode is cold, I have to do it manually so that the mode changes to heat.
I know it's ridiculous! It's because if it measures a temperature above what it's set to it starts blowing cold air ie you set it to 24 degrees and the thermostat all of a sudden measures 25 degrees... On comes the air-conditioning... It's driving me mad!
God, your Aqurea manuals are close to useless.... Explain deltaT: is this water outlet MINUS buffer deltaT of PLUS deltaT? Give an example. AND Zone1?? What is it purpose here? If there is no Zone1 sensor present, you get errror message on display, but has no effect on anything?
Our ducted systems can't seem to stay at a good temp, it's either not warm enough if we set it to 21°C, or it's too hot if we set it to 22°C, same with cooling, too cold or not cold enough, any tips or tricks? Seems like the logic overshoots on this.
My unit doesn’t stop when it reaches the set temperature. It keeps working with out stopping. Example if I set it for 25 degrees cool. And when it reaches that and passes to 23 degrees it still keeps working. Is there a way of fixing this problem Thanks
AMP Air Conditioning no the room temperature , how do I know what the room temperature is. I can see the set temperature but not the current room temperature
AMP Air Conditioning yes as in room temperature my old unit use to show to current room temp but this one I can’t find the room temp. It only shows the set temperature