Hi did you bought autoauth standard for unlock secure gateway? How did you do step by step for autoauth? Thank you, I bought autoauth standard but it’s not work for my car
I encountered a problem, the start-stop gives me an error. I mention that I bought a new battery, I put it in the car's memory and it still does the same. What do I have to do to make my start stop work? If you find video clips in this sense, please help, thank you
so glad i found this video, ive just done this earlier today as i started having issues getting into 1st and the inside gear knob holes were way off. ive adjusted it, there was a lot of slack on the left sided one which went with adjustment. took it for a little drive and it did seem better. ill go for a longer drive later when im not busy and check it properly. it started happening when the car was warm so thats the next thing to try later. Thanks again for the video.
One thing about the jack under that reinforced pinch weld is that that pinch weld will tend to bend when there's a flat jack under it. If you place a hard rubber hockey puck on the jack pad it will keep that pinch weld from bending. They also sell metal lift pads with a slot in them on Amazon to prevent the bending.
Do you have a video from the start 🤣 But thank you so much! I’ve heard VW interior is the same for Audi A1’s heat resistor, would you be able to confirm this?
i have an issue with the 1st gear only, it gets stuck or blocked by something on the way in, i have to comeback to neutral and go back in, or try to go hard on the left first before pushing forward
I have the same issue and i bought from amazon " replace for Gear Selector Shift Shifter Cable End Catch Pair 1J0711761C 1J0711761B Compatible With Polo Jetta GOLF Audi A1 A3 TT B6 B7 SEAT " and arrived today,,i didn't replace yet but if your gearbox its fine , the other issue can be are these two because of the bushes have broken from the years pass
Complimenti, io avrei preferito vedere lo smontaggio, ma il video è molto bello. Se avessi indicato Dacia Duster Techroad avresti avuto molte altre visualizzazioni, è il modello più difficile da smontare e trovare video tutorial, perché su gli altri modelli sono più semplici smontare le candele. Bravissimo
Hello mate. I need that door handle pulley replaced on my car. Mines has all cracked. Are you in london ? I have the part, I’ll pay you to do it for me please. Thanks
Thanks for making the video. Can i just ask if its ok to reuse the old bolt? I've read that it should be replaced, as its a stretch bolt. However all the video tutorials show the old bolt being reused. Thanks,
Thank you so much for sharing! Clear explanation and great demonstration. One Tip which helps with position of the measuring device. Open the bonnet and use for example the bonnet reststops to align the position (or any other left / right mutual bolts). You have the open the bonnet anyway. This will make it easier to ensure the measuring device is pointing straight at the headlight. Measuring the height of the bulb is an estimate but it can be improved by using a small laser light and leveler which points at the bulb. Then measure the height between floor and the laser light.
5:15 that is just poor advice there. Never hit a bolt in with a hammer. It’s supposed to go in by hand. Hitting it in is a good way to strip the tread off the bolt.
Thanks for your negative comment. however, I have been doing this a long time and I have yet to strip a thread by tapping a bolt in by hammer. Sometimes in this trade its a must, as a bolt Just sometimes will not just push in by hand.
Lol no thank god, the shows are well run and the referee's are on the ball. As soon as the child gets into a submission position it is stopped straight away 👍
Was the shifter sloppy during the up or down movement but otherwise fine side to side during neutral? Also when selecting a gear by holding the clutch first and right as you're about to get the stick into gear, is there a sensation of the stick not wanting to into gear unless you give it a bit of a push? If those are the the symptoms you were having i'll adjust mine tomorrow