@@markniblett4483 I don't know the steps to clear the MyKey on a 2017 Lincoln. All I can suggest is trying this procedure that works for the 2014 Fusion. Sorry I can't be more helpful
Sorry it didn't work for you. Just know all vehicles are different. This does work on a 2014 Ford fusion titanium, with remote start, amongst others. I don't know what vehicle you are trying this on. 🤷
Can the procedure you did of taking the key away from the car and everything else be done with the help of the forscan program instead of your video scanner?
The step where the key gets taken away is necessary so the car does not sense it. I'm not familiar with ForScan, I don't know if you can use that to reset the cases or not.. If you are using ForScan, you may be able to go in and disable the MY KEY settings without all the other steps
@@hellraizer50 In this case, you use your scanner to only read the DTCs and then delete them, is it only used for this in this process? sorry if the translation is wrong. I am from Brazil.
Tried dozens of times and gave up. Nothing worked. Tried 2 different code readers to clear the codes but they never would reset my cluster like yours did. Even tried clearing the codes multiples times on some attempts. Nothing would reset the dash. I drive a 2013 Lincoln mkz (basically a ford fusion) if anyone has any more advice
I'm not sure I understand what you mean. I don't put the key anywhere, I have the FOB with a push button start. Please be more specific so I can answer your question. Thanks
@@charliegoetia9765 the slot is in the center console. It's the same place you put the key fob when programming it to the car. I only use the slot in the video to make my fob a "my key" for the steps to remove the my key setting with only one fob.
Like ma y have stated this absolutely doesnt work. You never expkain where the code is when scanning which I did and nothing shows up thus this doesnt work.
They seem to be good. I can roll my windows up and down outside the car. The trunk button works also. When I try the remote start my horn blows and my fob flashes red 2 times
@@jasoncampbell7249 Is the check engine light on? I know that if it is on, then the remote start will not work. If it is not on, then I don't know what could be wrong.
@@stevocumberlandd5960 it should work on the 2013. Some people have said they had to reset the codes twice in a row, but I don't know if that will work for you or not. Wish I could be more help.
Hello I’m hoping you’re able to help, but every time I click clear codes on my scanner it’s giving me an error that there’s no codes to clear. Am I just out of luck at this point?
I don't know what scanner you're using. The scanner I used will reset the codes even if there is none showing. I would try to use a different scanner or if worse comes to worse, unplug a spark plug wire so you get a check engine light then put the plug wire back on and then do all the steps and clear the codes. I hope this helps.
When I close the door and got to turn it on it keeps saying my key detected? Any one else have this problem...BTW I'm using a modus ultra scanner for this
It's a 2015 ford fusion eco boost titanium... could it be that I'm using the wrapped in aluminum foil trick? I don't have someone to help at the moment. I'll try tomorrow once wife is home
@@jorgeescobar6372 I tried the aluminum foil trick and it didn't work for me, so I bet that is the reason why it is not working for you. You have a good plan to wait for a little help, I hope it works better once you have someone help you.
I tried it over and over on my 2011 Edge and couldn't bring up the menu to turn MyKey off. I have bought extra remotes from Ebay and Amazon thinking I will have to use Forscan to clean all keys them program new. But you need two remotes and if there not right your screwed. A idea how I can tell if the ones I purchased are the right ones or not??
Sorry this did not work for your Edge. As far as the remotes are concerned, they should have a FFC ID number. If they are the same as the remote you have, then they will work. Hope that helps.
I did not use a program. I used a SCT 4 programmer, but only used it as a code reader so I could reset codes. By resetting the codes / check engine light, it resets the cluster.
I don't know how to get it to work in your situation. I have had luck with a 2010 Taurus, by wrapping the key in aluminum foil and turn the ignition on, the key was not recognized as a "My Key" and it let me reset all MY KEYS. Good luck.
Hi, I have watched your video several times and tried with my own OBD code scanner. It's not working for me. I have lincoln MKX push button starter. Please, help me. Thanks.
I'm sorry it didn't work for you. The MKX must be different. I will try and figure out how to reset the mykey for the MKX. If I can find any info, I'll let you know.
On a 2016 mustang it needs one little modification whenever it asked to restart the engine my engine was running but I had to tap my button super fast because if I let the engine die completely without hitting it before it died it would not trip the my key settings but I did it super fast the engine didn't get a chance to fully die before I tapped it and turned it right back on that trip to my key settings and I reset it works perfectly thank you a billion times so much
@@hellraizer50 I tried the same exact steps and I did get to the restart screen but when I went to settings on mykey it wouldn’t give me the option to clear my key
Read through the comments, there is a guy named Carlos who had a 2016 mustang, it didn't work for him. He had to get a Bluetooth scanner, and download the Ford app for him to be able to reset his mykey.
I have a 2016 Mustang That has my key active and I went through the steps to try to get it off eyeball a blue drive off of Amazon erase the codes but it still pops up
Sorry you are having no luck. If you have remote start, and push button start, it should work. Try it more than once, follow all the steps. It may not work the first time. I hope this helps.
Sorry it didn't work for you or your vehicle application. 🤷. Many others have gotten it to work on their fusion and other models of vehicles. Let me know if I can help.
This worked on a 2018 Ecoboost, had to reset codes 2 times for the message “Restart Now or Key Needed” to pop up. Thank you has been bothering me for months.
Just worked for me!!!!thank you so much brooo 2015 mustang. I just started car normally with brake, gave key to someone to walk away with, waited till they got decent distance, then cleared codes like twice, turned off car(it says restart now or get key) restart the car, boom menu was there. Cleared mykey. Been trying to find solution for like 8 months
@@jasminemartinez8303 1. Start normally with brake. 2.Give key to someone and have them walk far away. 3. Clear codes like 3 times in a row. 4. Turn off car. It will say restart now or get key. 5.restart right after turning off in step 4 6. Menu should be there.