Thank you! I didn't have a clue how to start one of these. Your instruction works for other brands too!

Good job

I need a jeep

Our state never had a test in like 5 years

They have a retro kit to Eliminate with Electronic one

My Scrpto lighters just hisses and does not start

With removing the tow hooks, do you think you could still pull/tow from the bar without bending the brackets?

Guys this looks pretty serious, I don’t think it’s a test

Thanks for posting this.

goodold EASyPLUS

0:36 Forty Fu-

Darth Vader is working for NOAA conformed

Its steel

Dude when this guy said 18 years I thought he was gonna say since the last time he cleaned the damn thing

thx bro it worked finallyyy now I can go get high

“EASyPLUS”1:24

How did this clutch hold up? I just got a 855D and need to replace the belt, and possibly the clutch. Just curious if the eBay clutch held up

0:35 bro said the f word “Forty Fu-“

I just replaced mine, watched the 1st minute or so and that was enough to know it wasn't crazy difficult just looked worse in where it was positioned... appreciate the video, mine the rubber seal burst and was leaking quite a lot, I just got the whole brass unit €26, changed out in 2 mi utes, closed up, turned on worked awayno bother.....

That is a SLOW EOM lmao

The hydraulic jack was replaced but is still leaking. What's causing that. Then then I replaced it again with the old one it leaked from the top instead of the top. Then I replaced the cap and copper wire and then the top of that started leaking. What am I doing wrong. Any help.

I noticed you just hand tightened the retaining ring, whereas some people hammer it tight. Wondering your thoughts on that

Thank you I did follow your step and replaced the pump, first time in my life, very informative,

Dude… I feel like you just invited the wheel with this one, thanks!

Professional work, I'm gonna do to my 2014 f150 platinum 😂

Thank you for the instructions on how to assemble these carts and for the comparison of both. I went for the Harbor Freight because it had a better price. Good video, thanks a bunch.👍👍

Your neighbors will hate you, but only for 30 seconds

I bought my welding cart from Summit Racing for $125plus tax .065 percent much better than the other I found

For the first time he said a cuss word on the tv

Cool video. But before you do this, make damn sure the old contents of the drum were not flammable. Vapors can be just as explosive as the former contents, and guys have gotten killed just by drilling or cutting into "empty" drums that exploded. I was just reading about a guy in Pennsylvania who got killed by a burn barrel last week. And I know of another incident in Iowa that killed a man who was welding on top of a barrel, using it as a workbench. Filling the drum with water before cutting into it can displace explosive vapors, if done correctly.

Thanks

This lighter doesn't have a name on it and maybe that's why but it will not light but it shows it's got liquid of some sort in it, and this piece of crap will not light for anything! fast, slow, right side up, upside down, sideways, NOTHING!

You are a fucking genius! Thank you I appreciate you

Thank you

OMGOMGOMG it is so scaryI’m 😅

Ok so that"s not THAT bad

Theres supposed to be one coming up on Oct 4th? Yeahhh.. I’m unplugging every device in my house.

October 4th at 2:20pm.......

7 years later and they still work!!!!!

Looks great - very good video - thank you . Now I need to see what I can do with my 2003

I cut the trunk open left a trap door...no more dropping gas tank...nice job brother

Hey man, great method and I'll be using it today, thanks. BUT I do want to say... use safety glasses man. One of my technicians just lost his left eye from using the air hammer on a wheel bearing. The bearing splintered and shot to the back of his eyeball like a bullet, tore the retina off the back wall. He's blind in that eye now. I know pretty much every single "old timer" in every type of shop will say "I aint wearing those pussy goggles" but look man, I ain't going blind over here. No thanks.

It's not something I would do on my truck! However, it does look really nice on your truck.

THANK YOU!!

I remember the eas test in 2011 and it did not look like this

Can I have that TV

Do you think it can be done without removing manifold?

how to refill this lighter

THANK YOU SO MUCH YOU DON'T UNDERSTAND HOW LONG I'VE BEEN STRUGGLING

Loss my lighter so I'ma use this for my blunts