Welcome to MrFxr's channel, My aim is to fix as many things as possible, and to share that journey with you. Please subscribe, new videos are added weekly. I have been working professionally in construction industry for over 25 years and learned how to provide solutions for many issues. "There are no problems, just solutions", also I have been servicing my own vehicles since 1989 My educational background is Mechanical Engineering and Military Engineering Kind regards MrFxr
*Disclaimer: This chanel contains videos or video descriptions contains affiliate links. That means that I am awarded a small commission for purchases made through them, at no added cost for you.
Hi, is the camera or of reach from WiFi? Has it been working properly previously or are you trying to install it? If you're trying to install it done Ibis with on decko app and Adobe others work better with cloud edge app
@@marian_f1704 you could get one fresh strip from your local tool hire shop and try. It would be cheapest way to eliminate cartridges question. If it doesn't fire with fresh cartridges, than if firing pin issue.
@@LabradorSea to be honest, it would be hard to determine remotely. Can you send the link for similar window and I'll have as look. I thought than jeld wen only did timber windows, I've never got across uPVC one. It would be nice to learn about it
@@mrfxr1695 Thank you so much for your interest and readiness to help. I will try to locate a similar type and be happy to hear your opinion! Thanks again!
Is it possible to get a new powercord from Hilti ? My te55 got issues with a broken wire, just in the little protective bend, before the handle and the switch.
Probably it is, but it might be easier and simpler to just replace it with any other cable of same size. You can also shorten original cable just enough to past troubled section
To make disk space, can you delete the memory on the memory disk remotely or do you have to manually take the disk out and put in a new one? How often do you have to charge the camera?(In other words, when fully charged, approximately how long does it last before the battery goes out)
Hi, I'm not sure if we are about same camera. The one in the video writes on memory card, once card is full camera automatically rewrites over previous recordings. Also it is mains powered, not battery powered
If this has gone will this cause smoke and lack of acceleration currwntly got 2010 with smoke blue smoke not alot only wen stationed for few mins at lights then clears up trying to break it down lol
Great video.. I have located that screw, but very isolated..how many turns does it take? I've turn itva few times, but can't hear any air or see any liquid coming out. I don't want to risk the screw coming all the way out, as I won't be able to get it back in.. thanks
Process of elimination. You can test the plugs for continuity with ohm meter or multimeter, if plugs are good and fuse is good but not getting power during start up then it probably is a relay module. Also can be identified by scanning tool
got the same camera works fine with android app but cant register or get it to work on windows... any tips for me please i keep getn the captcha sent failed error
If only you had glued the dpm to the inner skin you maybe could have saved time and money but not knocking the leadwork and you should now have cured the problems.
How did you remove the throttle body connector? I am having really hard time. I can't even seen it. I have to feel with my hand and can't tell where to pull the tab.
Can't you just clean the window you take out and re-fit it. I have several like this and was thinking of trying that but is there are reason it won't work? Appreciate the posting thank you.
Good point. You could, but you would have to have expensive equipment for it. It is because there are two sheets of glass stuck together with hot butylene mastic (that's expensive part). You can't use silicone. Also, there is aluminium spacer bar all the way around perimeter and it's filled with silica to absorb moisture. That would have to be replaced as well. In short lines, it is cheaper to get few new units
I've just found the cause of the problem I had. The cause I had was from years and years of cr*p in the water outlet bottle there was loads of it. This could be a result of the area I live in - London having poor water quality because I that's all I put into the resevoir taken. So do what this video says and also have a damn good look at all the pipe junctions....ALL of them.
I'm not sure, what does it operate? Under dash F3 one should be 5 amp for air bag and pre tensioner. Fuse box within engine bay F3 should be 10 amp for windscreen washer pump. That should be on most of 207 models between 2006 and 2014, but I don't know if there are some exceptions there
Hey again. Do you know if 0W-40 motor oil is suitable for the 300c Touring CRD 3.0 Diesel? My workshop says no and would use 5W-30 instead. But the manual says that 0W-40 is always recommended for diesel engines. I'm totally confused.
I wasn't sure how to release the fuel lines and everything's so fragile. It worked like a charm thanks for your well explained video. To remove the top without a special tool I wrapped an old drive belt around it and clamped it tight with a vice grips. It gave enough leverage to unscrew it without breaking anything
I got the blue version of the same kit. Brilliant and great value. You can do most things with just 2 or 3 pieces, but has been handy having a few other things to try out when you’re stuck.
Thank you for mentioning that, it's nice to know that is not just me. I am genuinely positivity surprised with this kit. It definitely exceeded my expectations
Yes correct, constant velocity(CV) joint spleen of the drive shaft within wheel hub assembly , and they can be stubborn sometimes. So, 45 joules of impact power from demolition hammer makes life much easier 😉
For anyone wanting to get oxy-propane kit I found similar one on Amazon quite cheap amzn.to/3WYskFs Or bit more expensive one amzn.to/473bpX6 I'm not sure about quality of them. The one I've got is more like the one in second link
Everyone else I've looked at says you _should_ put plasticiser in ridge and verge bedding mortar (1:3 cement:sand mix so nice and strong). Not too much plasticiser, yes, but not none.
Plasticiser aerates the pug, so it is making it more porous. By building regs plasticiser shouldn't be used below damp proof course. It's because it absorbs more water thus it's more prone to frost damage and erosion . It is similar story with roofline pug work. Most of cement on the market is enhanced to improve workability anyway. Of mixed right pig will be smooth and creamy. Tbh I've stopped using plasticiser completely on any external work All the best 👍
Yep, pressure was fine, 2.2 bars. Water capacity(flow) was just over 13 liters per minute. This toilet requires a minimum of 20 litres per minute unfortunately. Not many properties in the UK will have that