This is my go to whenever I wash my cars. I finish it off with the Turtle wax Wax & Dry. Makes it easier to dry and gives it a bit of a shine. Water beads off a lot more too.
I tend to use more than needed a bucket wash. Just bought a cheap pressure washer and used it with an equally cheap foam gun and got surprised with how thick the foam was. Used the amount that was recommended and don’t understand the amount of hate this product gets for how cheap it is.
2:20 you shouldn't peel the plastic sheet of as it can pull everything out of the hole along with it....got at it with a razor blade and not just in one direction.
I fixed my stihl weed eater today with it.. it would only run if you held the throttle and would not idle at all on is own..I added some mib into the gas and let it run about 20 minutes and I can't believe it but it did work and idles great now.. it made me a believer
Nice that you got it running after getting it for free from the neighbor. There were some helpful things to see in this video. I have a BR600 (since new) and it is ready for some attention, it has never been cleaned or serviced in any way beyond air filter, plug and primer bulbs. I picked up a new carburetor just to have one on the shelf for backup and I also have a new coil (that I need to get installed) and a spare starter pull rope assembly. I took a look at this video you put up from the way you titled it, hoping to get a look at various things that would be involved with rehabbing a junker. I had particular interest in some things related to the gas tank. You left quite a few things out in this video. However way you managed some of the stuff, it worked out for you, but you didn't show it in this video. Thanks for what you did show.
I had engines that would not start after adding MIB, but after taking the carb apart they are perfectly clean. Inspecting the carb diaphragms they were very brittle so probably wouldn't start anyway. I run MIB in all my fuel just to keep them clean.
Milwaukee - Not really build to last. Longest lasting tools are corded Bosch and Makita Tools. Very well designed and well made and repairable too. They take serious abuse before failing, never seen a brand last so long with daily use. Problem with Milwaukee is they are all made in china, cheap components, cheap bearings. They also haven't figured some tools out like Bosch or Makita demolition hammers or hammer drills. The Bosch or Makita will last longer and work better. Also Milwaukee really doesn't like to sell you spare parts, they often group parts into assemblies that make the repair not economically viable. Cordless tools are always more prone to failure due to more electronics and the brushed cordless tools always fail first because either someone will burn the motor out or the brushes wear away, its easier to cook a brushed motor than a brushless one so I always get the brushless tool.
Dude said cutting deck is “too far gone” 😂 Shoulda figured that out the second you saw the big gaping holes in it. Yet you still wanted to power wash it. Have fun buying a new cutting deck for $600.
Oh no, I would’ve welded it had the damage not been so close to the spindle. The mower was free, and I now use it as a little yard tractor. Thanks for watching!!!
Wash in straight lines my guy. When you wash in circles, over time those micro scratches add up and become swirls but its harder to see straight line scratches when the light hit it. So in theory, the chance of micro scratches will always be there but circle motion scratches you will be able to see alot easier
My Daughter has the same honda Mower with the floppy wheels on it as well! I am going up to see her this weekend and will check out the wheel bearings! Thanks!
I have a frequent need to drag or tow something around my property. I have a zero turn, but I don't really like using it for that. If I came across this, I'd keep it as a tow vehicle.
No, it doesn’t. You’ve misread the instructions. You ADD it to the tank if the engine is running and DRAIN the fuel and add the MIB to an empty tank again, if it’s NOT running. Wait four hours then add fuel immediately and attempt to start. All these directions are directly printed on it.
A mi me salio malixima la sthil br 600 se rompio el arbol de leva hubo que cambiar carburador etc y no quedo bien todo esto con un año de uso profesional