I have a F6+ Hota charger and want to update the software. I’m unable to do this task. Tried all the tricks I have seen on RU-vid. Do you have any suggestions? Thanks.
How do you get contact with you for help iv spent the last 5 days no sleep non stop working on my wizard 220s bought assuming it was set up ready to fly I cant connect goggles and it won't allow all controls on beta to move only switches when I pitch or role I get 0 movement on the tabs but it is connected and on the correct uart I have my pid settings sorted but no movement
Also, you're wrong at 5:20, Mode 3 is console gamer fer sure, and it looks like this: *RC Drone Controls (Mode 3):* - *Left stick:* - *Pitch (up/down):* Equivalent to moving forward/backward in an FPS. - *Roll (left/right):* Equivalent to strafing left/right in an FPS. - *Right stick:* - *Throttle (up/down):* Equivalent to aiming the crosshair up/down in an FPS (elevation). - *Yaw (left/right):* Equivalent to aiming the crosshair left/right in an FPS.
The real reason they don’t want us to have Drones is because they don’t want us being able to use them against THEM. it’s the same reason they want to band guns. They say it’s the same lives, but it’s not really it’s just because they don’t want us having them. The government wants to be the only ones who are allowed to fly drones.
Another idea is think vertically. You can put a VTX relay system on a slave wing loitering or circling above on GPS. To increase range and ability to drive into the tree line with the master multicopter.
I have a home-built quad, as well as a DJI Air 2S. But my opinion has always been: where’s the American equivalent??? I’d be happy to buy one if it existed. Where’s all the American ingenuity?? A year later I’m still waiting
@@mikeallenfpv 3 ... well ok, until i got my last penny together to buy the SKY04X Pro ... Analog will never be the same again. only keeping 1 HDZero quad + the v1 VRX, for sentimental reasons. gifting all the other half-broken HDZero VRXs and cams away.
HDZero doesn’t mess with time. One can fly through digital static similar to analog static: the image may degrade momentarily but it is still in real time. Mountain diving with HDZ is a good use case for low latency, real time video (so I’ve heard 🙄😇). Scraggle needs to be visible even if there is static.
And then fail to realize you made it hard for US companies to succeed by voting for the ones that restrict innovation & let free from regulation China walk all over us
My 1w hdzero vtx outperforms my 2.5w analog vtx. People think hdzero has horrible breakup but what they dont realize is that analog in the same situation would be unflyable. Analog causes the whole screen to warp, change colors, lose colors, and bend while hdzero is just missing pixels with a perfect image still.
Yea, I’ve gotten great penetration performance with HDZero as well. All about antennas. What I like about HDZero is the image never freezes & the resolution doesn’t change, so even with 90% static it’s still easy to navigate.
@@GiantAntCowboyAgreed… we do the same style of flying… er… Stag and Bullwinkle do. 😇 The “clear image” fallacy is one of the best drivers of sales for competing digital video systems. Since desert flying means proximity around rocks, there are areas where NO system will penetrate and one just has to squeeze the cheeks for a second or two… In that case, one HAS to have a realtime recovery image to make piloting decisions on egress. The best penetration comes from 1. equipment confidence and 2. real world training.
@@jeffparisse4202 I’ve recently started testing DJI O3 & I’m super impressed, but when flying near mountain peaks & ridge lines I can’t relax. Constantly looking down at Bitrates numbers & expecting the image to freeze & disconnect. With HDZero/Analog I know static will appears moment there’s any sort of LOS issue, and then I can just correct. (As you said) All these systems are great, and what’s best is dependent on use and user expectations.
There's a limit in the bit rate that HD cams can send - it's impossible for the transmitters to send 1920x1080 pixels (and even lower resolutions). The bit rate is what decides how much data can be sent - and it's usually not that much (in terms of video data); there's just too much information to send for it to be possible to send the raw data. In fact, assuming it was 8 bits per pixel, which likely is on the low end, it would be 2MB per frame, or 120MB (megabyte) per second @ 60fps. This is equivalent to 1.6 Gbps (gigabit per second), which is around/higher than the speed that fiber internet can send - and we aren't flying around with fiber optic cables attached to the drone. To send 1080p video to your goggles, the transmitter does a lossy compression, which losses some information as it tries to keep the main pieces of detail still visible while scrapping everything else until it reaches the point that the data can be sent over. The less detail there is, the less the algorithm has to scrap. But when you get hundreds of branches & thousands of leaves in there, all moving, there's simply too much info to be sent over. So, the compression algorithm makes lose some of that detail in order to be able to send the video to you. The best visible example of this would be Tom Scott's video on bit rate, "Why Snow and Confetti Ruin RU-vid Video Quality". While the video is specifically about youtube - it's main topic is about bit rate.
an idea for a 3d printed frame could be to make as lightweight as possible, maybe using generative design like fusion 360 has, and then having some form of lightweight metal tube in the arms mainly to provide support, and using something like PETG or ABS
I've set the "set sbus_baud_fast" based on other tutorials... and it still didn't work... I then thought, "let's see "what we can learn today"".. I found this video, and I learned that forgetting to type in SAVE after the CLI command can cause a 3h back and forth "setup" session. Almost started to think that I'll need to do some re-wiring... A Big thanks! Btw, huge fan!
Hi Joshua i have a problem , the capassitor came loose on my speedybee 405 v4 55a and it seems like 2 components burnt have you ever had electrical layout or components list for the esc
