Hi, this looks like an issue that has just developed on my car. What type of cable did you use to jump lin connection, just a bit of single core copper? And also, if one side of plug terminal looked damaged, will this require repair to both plugs, male and female, how do you remove plug fixed in b pillar? Many thanks, great video and informative.
how much time you used to clear the adblue malfunction light? I am also facing this concern with no code after I replaced adblue pump and NOx sensor. I have tested for 400-500 km but the light is still stayed on....
Thanks for posting this. Just serviced and fitted an HEL brakeline to the passanger side rear brake of my 2023 2.3 Ecoboost ST4 with no dramas. I unplugged the brake at the caliper just for good measure. Drivers side to do tomorrow night.
Hi I have a mk8 transit custom. Fault code p1762 clutch pedal A clutch position correlation. Live data showing clutch pedal is partly pressed when it's not. I replaced both switches on the clutch pedal. It will only start by pressing the brake. Stop start cruse control tpms not working. Any information would be a great help.
@@farredmuflahi8958 I'm sure that the Invitation code is just for the forum? To register the license it can be done on forscan site. I plan to re make this video for 2024
PATS is such BULLSHIT! It requires TWO Factory OEM Keys to be stored for it to work. No you can not use an aftermarket garbage, it has to be real OEM Ford keys. I have three keys: one OEM and Two Aftermarket. After a PCM Swap, PATS tells me to Fuck Off as it will not accept the aftermarket keys. Off to the dealer to sell my kidney for the second OEM Factory Key.
Hello I have a problem with a ford galaxy 2010 petrol engine, on the dashboard , key not detected, immobilizer active, engine malfunctioning, none start, fob key not opening car i need help , i have used 2 electrician who have diagnosed and promised to come back till today I am yet to see them
Hi , working on 2021 renault clio fault while driving everything cutting out for 2 seconds engine , power steering and no dash lights , speedo rev counter etc only does it in the morning after a few minutes of driving , no codes could the bms on the battery cause this and would it be okay to disconnect this or bypass it to try it ?
Hi mate need help got forscan an apparently need to replace egr which I've had off before which is no issue but apparently I need to resert values and calibrate new one any help into where I find this in.
Hi mate, love your videos. I used to be a technician before I became a lawyer. Now I have little time to work on my car unfortunately. My timing chain needs doing on a f10 520i n20 engine. Is this a job that you would want to take on or do you know any really good technicians that would be able to knock this job out? I’m in London and I’m struggling to find any good technicians in London. I would just do the job myself but I have no time and it would be more cost-effective for me to just pay someone. If you can’t help, thanks anyway.
Thanks. My driver side centre air vent wouldn’t close. I knew there was a small link inside that can come adrift. I watched this video, popped the vent unit out and pushed the lever link back in. Reassembled and all done in less that 20 minutes 👍
Don’t know if you will see this, but I have the same model sync 2, on a Kuga 2016. Randomly the left front speaker will start to distort very loudly, turn off radio or car for a while and it will work normally when turned on again, after random time, it will distort again. Very annoying as even with the radio turned off, the distortion will happen with the reverse sensors and phone calls coming through speakers. Any ideas?
I have seen this fault and also noises from the speakers with radio turned off. It has turned out to be the radio unit itself. But I advise diagnosis first
I am trying to understand how you can have multiple sensors on one feed and all have 5volts wouldn’t that draw all the 12 volts down to low on some sensors. I was assuming each one draws like a light bulb draws down current 🤷🏼♂️
Do you have to do the wire or pin swap on both sides, driver side, and passenger side? Also getting an error. I’ve tried the only Fxxx-xx since I have a 4key fob, do I need to use the FC code, tried without didn’t work then I did it with FC didn’t work. on the driver side and I’m getting a short ground error on the DTC on the driver module wires I had to cut a wire and resplice it wire a 3m connector. No errors on the passenger side module just on the DDM. What do you suggest?
Do you have to do the wire or pin swap on both sides, driver side, and passenger side? Also getting an error. I’ve tried to since I have a 4key fob, do I need to use the FC code, try without didn’t work then I did it with FC didn’t work. Too much on the driver side and I’m getting a short ground error on the DTC on the driver module clip the wire a 3m connector. No errors on the passenger side module just on the DDM. What do you suggest?