This channel is focused on the hobbies I enjoy in life - firearms, old tractors, tools, and my truck. My desire is that the information I present is of practical use to you. Content will be produced as I have the chance the make the videos. Thanks for stopping by!
Bro, lololol, you are right on the money! The chrome lined barrels, are the same deal, lol. PSA and BCM both get there chromed lined barrels from FN!! 😂 I figured a longtime ago that the PSA and BCM triggers are the same also, probably made by FN also. I remember 10+ years ago it had came out that FN was supplying PSA with chrome lined barrels, most of which were stamped/roll mark was right on the barrel, "FN." BCM about 10 years or so, some employees let it slip, they get there barrels from FN. FN the company, manufacturing is up the road from one of PSA's stores and they have a good relationship and had a contract with FN for there chrome lined barrels and other parts!!
Thanks for the video. I'm planning to buy a 1975 John Deere 212 with missing lawn mover deck. I'm unable to find one on ebay (UK/EU). can you help me, what are the constraints, compatibility considerations ?
Nice Rifle ad a 270 ,last fall a nice 10 pointer came out were I was sitting first shot missed the second shot the rifle Jammed ,no problem took the rifle out the next day first chase of the day I could hear the Doggers coming in the distance when the Biggest Doe I ever seen in my life came out of a swamp and righting front of me ,with no clue I was sitting there looking at her pull the Hammer Back and could not squeeze that trigger for the life of me ,the rifle Jammed again ???? after the Hunt sold on a trade as a malfunction rifle ,,,tomorrow I'm trade in a Marlin 336 35 Rem for a 308 can't wait the get it ,,Browning is a really good gun and that's it great Video thanks
I have a 212 that I purchased with no engine. I installed a Predator 420 from Harbor Freight and it works great! I also put on a sleeve hitch so I can use certain implements on it. I too dislike the whole belt drive system on it but it is what it is.
Probably would cost 3 times as much today. Cost of aluminum has skyrocketed. I have same situation--outdoors with block wall. I have 8 feet to be mounted to block and 6 feet mounted to siding of first floor. I am purchasing two 10-foot pieces of 1.25" (1.5" OD) EMT from HD. EMT is galvanized steel and won't corrode or rust. From Amazon bought a set of 6 stainless steel brackets that support the poles from screws underneath--that's about $60--they sell cheaper ones costing a third of that, but my staircase will be used by outsiders, so didn't want to skimp. And Amazon sells a set of 4 end plugs for $8. So mine will run about $130 (but could have been as cheap as $95). Not bad for 2023. I went to a local building supply to price aluminum poles and brackets - $350 (8 foot aluminum 1.5"OD is $100).
I've got 2 complete PSA lowers with MOE furniture and EPT, around $135 +free shipping on SALE I cant remember when but it was a big sale ( i.e.: Black Friday, Memorial Day) big holiday usually = big sales. anyway I love everything about these lowers especially the price...BUT I HATE THE MAGPUL FURNITURE! yes i said it, the MOE= cheap version had no QD mount on the stock and for that itself I can stand the Magpul stock, in the future I will definitely give up the extra $20 buck and get a B5 system stock which is way above the Magpul. If you catch them at the right time you wont beat PSA
I spent many, many hours in the seat of our E3 on our farm in Oak Bank, Manitoba . We had two E3's, a E2 swather, a E7 combine. When you started it up it was music to my ears! Speaking of ears, I think I can thank the E3 for my hearing, or should I say LACK of hearing!! Thanks for the memories. Jim.
I have one just like it, but with a 14" bar. No major issues with it & everything on it works properly. Bought it in 1985 at Best Products in Dayton, Ohio. Think I paid about $145. The anti-kick back tip fell off in the late 80s. I cut a lot of osage orange out of the fence row with it back in the day.
Just a thought on this video which you put it a few years ago. Thanks for doing it btw. You could put another foot like you did the wall anchors, and then a vertical support post off of it up to the unsupported end
I have one - they are very ammo fussy in 308. The heaver loads only pop up from the magazine correctly if you only load 2. I use the sako gamehead 123grain and they cycle flawlessly. You are better off with lighter loads anyway in that gun as it will kick hard otherwise.
Where did you buy the footings exactly; I can't find these at Ace, Home Depot or Lowes...it's exactly what I want for my railings. I want footings that are 1 1/2 inches square or rectangular...please help!!
If itvwon’t start without a squirt of fuel it’s because your carb probably isn’t set right or improper starting procedure. Verify your carb is together right and all orifices free and clear, make sure float height is set right. You need a gauge for that. Then choke on full and homd the throttle 3/4 open. It should fire up in 3-5 pulls. If not your low speed jet may be to lean ( not enough fuel). The carb needs to be tuned right or they won’t cold start well. Mine usually starts first pull.
I have the exact model bought new probably 30 years ago. It has been run sparingly over those years, but has original bar and blow molded case, but I've replaced the chain a few times. Other than a bit of a pain to add fuel to get around the hand guard it has been a terrific saw. For its size it has good power and is very light . Good saw
Give the old girl an engine rebuild and she last another 74 years. Love seeing old iron still being worked, I have a 45/54 Farmall A that runs ok I suppose (could use rings). It too has a transmission noise but it sounds like 3 wolverines in a bar fight, so I'm gonna keep using until something happens lol. Nice demonstration of your families tractor.
A detailed item description and or the name of the manufacturer of the pieces used would be very very helpful. Then we can utilize said information to help us find a supplier in our area. Thank you in advance. ....
Hey mate would ya mind adding me on Facebook or Instagram I’d love to ask you a few question; picked up the Canadian Version, the Cockshutt 30. Not gonna lie didn’t grow up around this sort of thing so any guidance would be hella appreciated!
I know you're comment was a year ago but just wanted to say, I'm pretty sure aluminum won't get as hot to the touch. That's why I'm thinking of using it. Also no rust but yeah the black pipe will last a very long time
