I love it, I took screenshots and everything so I can make one this weekend! I just got a free 40" LCD for the kids room with no legs, and a broken mounting hole in the upper positon on the back of the TV. This will work perfectly and it only uses the 2 bottom holes. I"ll need to make 2 little legs in front though that fir into the base, because there are buttons on the bottom of the TV. It will still be low profile becuase I'll only make the legs an inch or two high so they can get to the buttons if needed.... lol Thanks for the great idea!!!
Since I took the plug out of my E46 N42 sedan, the car has consumed a lot more gasoline and drives extremely slowly and barely accelerates. Valvetronic broken. How long can I drive without this plug?
You mean basic tools and 2 hours max? You could do all of this with a circular saw and drill. You don't have to router out a space for the tv to sit in.
When i disconnect mine it runs fine. Haven't yet driven without it connected but considering the Price of a new sensor is more then I paid for the car I'm thinking about driving it without it connected. Anything noticeable?
Absolutely not. The watch has an indicator when the battery is low. The second hand skips 5 seconds. And then when the battery hits critical levels, it stops moving the hands but keeps track of the time, and the day complicatin never needs setting, as long as you replace the battery before it comeptely dies. Even if it does, I believe that by using the Longines app and flashing the phone with your phone it will reset the phone.
@@aidilj muito obrigado por me responder, eu estou no momento planejando fazer ela, só o que estava difícil era saber qual display lcd e placa-mãe usar, mas agora o difícil é saber como fazer a programação, mas mesmo sendo difícil vou tentar fazer assim que possível, se der certo, eu faço a postagem junto a sua no thingiverse.
Thats the eccentric shaft sensor , A new seal and gasket is cheap directly from bmw dealer. Takes 5 minutes to change and the clean both connectors out with an electrical contact spray. Allow to dry and plug it back in. Job will be done.
Man id love it if you had the code for the controls; mainly for the appropriate joystick values. Do you recall if your x/y axis had anything special or just a map function if < 117 || > 137. I feel like the control on such a small stick might need to be (minimized) to make steering smoother.
This is so cool, exactly what i'm trying to do for a little project. I've got a couple of questions for you and i'd really appreciate any info: 1. how did you get the USB host shield to work with the 5v pro mini? (I though this would fry the board. Or is there some sort of regulator that outputs 3.3v to host shield?) 2. Did you have to do the 5v hack (cutting the trace/routing power from 5v RAW on host shield) for the bluetooth dongle to work? 3. What kind of range do you get with the controller? (Does the nav controller re-pair if out of range/back in range)?
Glad to see I'm not the only one with this idea. It's the perfect material for a belt printer. The sand paper give the belt plenty of extra grip, or if you don't want the sand just soak the belt in water and it comes right off. Sandpaper has some kind of stiffening agent that's water soluble.
Finally I can comment you can order a cr 30 belt from creality you'll have to season the belt with bed adhesive for anything to stick bu you'll be able to utilize the WHOLE BED
For me, the Longines build quality is almost the same to the Rolex, since the movement is quartz probably they are able to put more work in everything else. I like the more substantial bracelet on the Longines, felt more balanced. Tech wise, the Longines wins with high accuracy quartz, flash setting, easy swap between home and travel time, sleep mode etc. Its the watch that is always ready to go in my collection other than the Casio. I suggest you visit an AD to have a look before deciding. I no longer have the Air-King, replaced it with Omega Globemaster since I need the time zone setting and having a date is convenient.
Интересное решение, но проблема в начальной точке опоры. Первые слои фактически в воздухе. А вот механизм съема детали со стола очень даже хороший, нужно только подобрать ленту, в идеале даже термостойкую, чтобы печатать не только PLA.
