They do this shit all of the time near the salt river outside of Phoenix.. McDonnell Douglass is in the area and so are the training grounds .. Scared the shit out of me.. This isn’t Phoenix though .. Definitely having fun with it
I was taught nealy 55 years ago that you shouldnever use the old oil. Many times it will cause the gasket to stick to the housing. I have always used the fresh oil and havenever hada gasket stick and I change dozens of filters per year.
I've hat the o-rings stick to the housing on a couple occasions. That is why I always mention that you should check the filter housing for a stuck o-ring. I've never heard about the old vs new oil. What about the old oil causes the o-ring to stick? I would think if you change fluids regularly, the oil properties are still all good in the used oil, especially when running synthetic.
had a similar experiance about 10 years ago when i was on a motorcycle roadtrip through the US with my dad. we where driving along a highway through washington state when all of a sudden an F18 did a low flyby only a few meters above our heads. nearly gave us both a heartattack since it snuck up from behind.
Thank you so much for making this video for others to use as a guide. So much appreciated. You by your actions helped extend to boarder of heaven right here to where i live.
Quick clear, in focus, didn't waste time showed us what we needed to see. Very Nicely done! Thank you. (I'd prefer to skip the music, but it seems like everyone feels they need some front end music for branding....at least you didn't play it while the presentation was ongoing).
Nice video yeah I just took mine in I pushed my service to 165 hr for first service and it ended up costing me $300 but I did regularly blow the air filter out and check oil level . What size is your center hole on your blades I ordered the same gator blades I have been ordering and they were way too big
Thanks for the question, and thanks for watching the video. In the video, you can see I used an impact gun to remove the bolt for the blade at 2:36 . If you use an impact, you don't need to jam anything anywhere. Just like when you use an impact to take a wheel off, it doesn't spin the wheel even when off the ground. Same concept. You can also read other comments that nice people left asking about what impact I used as well. Thanks again for watching and leaving a comment.
Thanks for the video. Question, have you also tried not bypassing the Starlink router and configure the tp-link mesh as AP? Im planning to do this, just wondering if you or somebody else tied this set up. Cheers, Sergio
@@schmitty750 not sure! I thought keeping the Starlink Router will allow monitoring the conection, obstrucion, etc. Is like that? Or you can also access de Starlink app with the Starlink router bypassed?
The starlink app works with the tp deco router. You can also monitor who is on the wifi, create visitor passwords that run slower speeds so they don't slow the primary cinnections.connections. You can see obstructions in the app as well.
If you cut the outer sleeve two inches and not the inner, the shaft will still only collapse to the original length but the outer sleeve is two inches shorter (inner is still original length so cannot collapse by two more inches). Vise versa, it's the same. Both tubes must be cut by 2 inches to be 2 inches shorter. This was probably not the best way to explain, but this is how my brain works I guess.
I have a new video out for changinging the front wheel bearings... mine went bad in a hurry 🤣 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-lHnKCWeON4s.htmlsi=S5n_-b51NJ9cCgOT
One of my favorite things about the mule is that I can work without getting mud slung all over me. So I didn't want the tires to stick out from the wheel well. If I was playing with it more than anything else I would for sure get spacers just for the fact that it would give a bit more confidence when it leans over on a steep grade. Thanks for watching!
@@schmitty750 i had that same kind of thing happen to me on a ford ranger, except all it was, was the aftermarket floor matt some how scooched between the pedal and the floor board after I was trying to give it all the beans LOL
@@schmitty750 really?! 🤣 yea I felt like a dummy because I popped the hood getting ready to take things apart to realize it was just that! I bet you were relieved it was a free fix!
