How does it ride @offthejeepend ? Any harshness or front end fully flexing out over bumps?

Great video exactly what I’m looking for! I think that plug that wasn’t plugged into anything is an OBD one connection

Baby video great video straight to the fucking point not 20 minutes of bulshit beforehand during hand and at the end this is how I like to see videos done 25 thumbs up

So who knows what the result was,very poor

Did this exact thing in my CJ years ago

😂😂😂 WTF You just fuck up the Jeep with that mounstrosity 😂😂

Tell me what rim and tire work with it like some thought Jeep Wrangler jy

Dude your a life saver let me try this on my yukon. I had a hose leak in my passat before I have to go through hell the high pressure hose cost me 400$ similar hole like yours due to rubbing on the belt. I sold that vehicle I wish I have seen this video earlier.

Thank you for the video! I have a pinhole in my AC line. I will definitely give this a shot. Thanks for uploading. Very helpful!

anyone know what the tube on the heat shield is for? (you touch it at 1:20) It not connected to anything on all the 2.5 i've seen and its driving me nuts

Just,pulled my rear track bar off my 91 YJ last week. What a difference!

What size jack did you use

I want to put it on a discharge line, that is leaking where the rubber is crimped to the aluminum. Does it bond to rubber?

Dude, next time you do a tutorial, finish your thoughts and actually show us how to do things

I love stock jeeps and cars.

Did you cut the floor brace or no?

I have a 89 YJ and a 07JK. Those JK rims don't look right on the YJ. Two totally different eras.

Shut up bruuh

So how is the transmission all this time later?

The book says to use Dex/Merc 😳

My 93 2.5 do the supercharger thing, is derpy but I like it

Hey question about your power steering bracket. Was that stock on the YJ or was that some sort of TJ upgrade you did? The other power steering brackets I see look different. Nice video btw very helpful

Good job man, you do what you have to do.

Rube Goldberg: The Master of Absurd Machines Rube Goldberg was a cartoonist who drew absurd machines that performed simple tasks in complicated ways LIVES ON in JEEP engineering.

Thanks for taking time to make this.

Could this be done with bolts and large washers without the nit strip...

Where can i get this stuff from?

For ac lines that have a hole or crack.....I wonder if you use shark bites???

Thank you so much for this video!!!

Any recommendations of why YJ wouldn't start after a simple fuel line (had to replace a section of the nylon tubing on supply line) and quick connect replacement on both the supply and return lines? I get sufficient fuel running through the supply line when disconnected from the fuel rail but as soon as I hook it up fully, I can't get a start.

I swear i couldnt ask for a more detailed video. this was perfect. I just got some rusted dorrs with problems since brand new ones cost hundreds, and these ones off face book marketplace i got for $80. need paint, but the internals needed to be oiled but I didnt know how to open them. thank you

Great Video. Where did you find the return and supply lines at??

Never seen this done on RU-vid before,some item part numbers used would help others

Any idea what the torque is for the fuel pump gasket bolts?

Are the gas lines (hoses) different sizes? Also, you said the ‘top’ line goes to which fuel line on top of the fuel pump?

Finally a video of reassembling the ‘dropped tank’. I hope I put the fuel intake hose in the right fuel line.

I bought 5 17 inch. Tires were fact with 300 miles for 200 dollars. Will they rub with stock suspension? they are basically 31.15 size

WhT does this due I’m a YJ owner

Thanks for the video, great detail. A tip for anyone doing this, the sawtooth pieces are setup to be inserted/removed from the top. There is very little room to do this inside the door and it is very difficult to do on some models. Before you put the new handle in the door, remove the metal clip that engages the teeth on the sawtooth bracket, and flip them around 180 degrees, so they are upside down. NO tools needed for this, easy to do with fingers. This will allow the sawtooth brackets to install bottom-up, when in the door. There is much more room to access this way and makes the job much easier.

Atf type 4...

You are supposed to use atf type 4. If you didn't you just phucked up. You can use Lucas all day long but must be atf type 4 not universal type. You just destroyed what was left of you transmission

ok, 2 years later how about an update? Did the Freon seep out over time?

Are all the bolts inside 14 too?

Just bought a '95 YJ on 35's and drove it from NJ to Texas. LOVE It! I have to adjust e brake for inspection here. Junk yard ebrake conversion next. Thanks!

Outstanding Idea!!!

Hey do you remember what size bolts you used for the front of the skid plate

Great vids bro. keep them coming!! 👍

Will this work on the ac compressor

FYI to other YJ folks - the NAPA brand replacement interior handles hold up well. You can order them online and they come with the appropriate clips to lock the rods in. The clips that come with the new handle are not the same ones that come in the repair pack of clips. The ones on the handle are better by far and hold up quite well. The new interior handle will also make your now over 27 year old YJ look fancy.

Cant you cut pipe and slip a coupling on it or put rubber hose with pipe clamps on it