There is no way I would use a microwave that had been painted/scraped rust off. Toxic fumes is NOT a good thing. just buy a new every now and then . Your health is was costlier if you get sick
The explenation is very simple and I really appreciate that, but it would help greatly if the switch that you are talking about is kept within the video frame
4:50 So my problem is it won't come off the wires, 2 metal "crimp" ends with 3 slots are connected to the contacts of the switch & they won't budge even a bit. like the wire you have on your second switch. But i can't figure out how to get them off so i can put the new one on, & i already broke the top of a clip of the switch holder trying to do it.
Good job - very helpful. If I were to add any comment it would be regarding the correct switch for the correct position. Users changing switches need to ensure they replace a NO (Normally Open) switch versus a NC (Normally Close) switch. Therefore, users should be mindful of the type (NC or NO) switch they are replacing.
Some friends just gave me a microwave they had in storages..it looked really clean but when I looked at the top I noticed several rust spots..smaller then those..thank you I'm going to fix them how you showed it...and leave door open after using 😊
Just wanted to say thanks on how to remove the interlock switches for the microwave door latch. I studied the heck out of them. All 3 have a slightly different approach so as to not break the post that anchors them. Again. Thank you. One suggestion. Try to evenly light your projects from the start. Looks more professional and you're less likely to lose a viewer from the get go. Trust me. I worked in tv production for over 40 years. Yes. I'm an old fart. But I do appreciate when an honest effort is made to help us folk out here. Kudos!
I noticed on the right side panel, looking in, there's a square ( approx. 4"x4") looking unfinished spot at 0:52. What is it and is it supposed to be like that. The reason I ask is that I noticed a spot like that in mine.
Can you appliance paint from a spray can spray it into something then brush it on. Would it be a good safe idea to use Rust-Oleum rusty metal primer brush paint first? Thank you!!!
Rust-Oleum Automotive Universal Touch Up Markers : Toxicological Information EFFECTS OF OVEREXPOSURE - EYE CONTACT: Causes Serious Eye Irritation EFFECTS OF OVEREXPOSURE - SKIN CONTACT: May be absorbed through the skin in harmful amounts. Causes skin irritation. Allergic reactions are possible. EFFECTS OF OVEREXPOSURE - INHALATION: Harmful if inhaled. High gas, vapor, mist or dust concentrations may be harmful if inhaled. Avoid breathing fumes, spray, vapors, or mist. High vapor concentrations are irritating to the eyes, nose, throat and lungs. Prolonged or excessive inhalation may cause respiratory tract irritation. EFFECTS OF OVEREXPOSURE - INGESTION: Harmful if swallowed.
Folks who have painted a cast iron stove know that there is a difference between the many kinds of "normal" paint (like automotive paint) and paint designed for high heat. There is such a thing as oven paint or microwave paint or cast iron stove paint: They are made to withstand high heat and avoid emitting toxic gases in high heat. Pro painters also know that when one is trying to paint a patch, feathering it in smoothly with existing glossy paint (like on any appliance), it is necessary to lightly sand the existing glossy paint with a fine grit sandpaper (like 220) so that the new paint adheres well with the old paint and does not flake off later. It's the same principle used to resurface roads, glue nonporous materials, etc. For all these reasons, I really appreciated a different RU-vid video "How to repaint inside your microwave - fix interior rust and peeling." I'm not related or friends with that RU-vidr -- I just think he did the job right, matched the original color well, and produced a result that would not have to be redone later.
why did nt u shows the reading of the good and the bad capacitor? People wanna see the reading to see if its good or not. NO reading means its good. reading means its shorted out. Ur confusing people.
He explained and showed everything you've asked for. If the cap is shorted then it would give 0 ohms (or just few ohms) of resistance between its terminals and that's exactly what was shown here when the needle of his analog meter went straight to zero ohms. If the needle didn't move (or the reading was O.L if the digital multimeter was used) then you would know that at least that cap is not shorted. It could still be a bad cap, as caps may fail in few different ways (and short is just one of them) but to test them for such other possible failures you'd need to have some other equipment. Finally, if you don't know what you're doing or what to expect, then it's a good indication you shouldn't do this for your own safety.
Liked the video and knowledge how to repair. I have only had my midea microwave for a year and rust has really set in. Just hope I can get the paint you suggest here in South Africa.
First I thought if I replace the fuse problem solved. End up replacing the capacitor. Still the fuse burn after few seconds when trying to cook something. What would be the issue?
Outstanding video is right. You're a great teacher! I know its difficult to video yourself, but if more of the object your working on at the moment was in the picture, would be a perfect video.. God bless
Hi CJ -My GE JVM3160DF4WWW is 1.5 year old. I installed it with a friend. Symptoms: At times after using Microwave and removing the cooked item, the Microwave light and low fan come on by themselves. Also when setting the Microwave to cook.,the chosen number of minutes is shown in the display but sometimes the Microwave will not start unless you open and close the door and re-press the start key. In both situations, the problem was related to opening and closing the door, so I think one or more door switches have stopped working properly. From what you say it appears that the bottom switch may be the defective one. I admit I might have caused this by stopping the microwave by opening the door instead of hitting the stop button. My major problem is this: I was able to install this over-the-range microwave with an assistant. It was very heavy and not easy to install. I dread the thought of removing the microwave to attempt to fix the problem. I realize this is the preferred way to do this as one is encouraged to defuse the microwave to prevent a dangerous shock. Is there any way one can safely test and remove the switches without removing and opening up the Microwave? There are a few DIY videos where it appears the grill and control panel is removed, the switches replaced through the front without diffusing the capacitor. Is there a safe way of doing this?
Great video. I'm curious as to what type of light and bulbs you used to light this scene. It gives it a really cool/epic look. I'm into filmmaking/photography and would like to get a cool look like that. Thanks!
My god if mine looked that good right now, I would be thrilled. I think the customer could probably fix it themselves if they had half a brain. But you were the wonderful person that took care of it. So you got a few bucks and in the process taught us some good tricks. Thank you thank you thank you.
I just found this video after putting in more details into my search criteria. I wasted time watching others remove switches with different brackets. Thank you for showing the details on this! I finally got the switches out!
Thanks my microwave has a 1 inch hole at the bottom due to corrosion, how do I fix it, can put in a bathroom filler and then paint it with the substance that you just used? thanks
what is triggering the flame coming out of the side, the only place rusted is a very thin line at the door opening, even tho' I wipe it and put an absorbant cloth under the glass plate
