Hola muy buen video.. tengo una maquina dtf es la r2000 dx5 y tengo un problema cuando imprimo azul me salen unas lineas blancas horizontales pero solo en ese color y no entindo porque..
This type of flock paper used in conjunction with a screened on adhesive is impossible to find in the USA. Only the kind used with a laser cutter is available. I'd like to buy it myself.
hola quiero saber si tienen algun video que me ayude a solucionar , mi printer esta llegando solo a una parte del diseno y despues se detiene, tienes algun video , tengo un epson l 1800 dtf , gracias por tu ayuda
Good morning I have a new modified Epson L1800 for dtf but when i start printing there are small bubbles like foam rising from my wast ink pad to my print head. Then i have wast ink on my paper. Can you help me with this problem please
Please I just bought an Epson L1800 to be converted to DTF printer but someone said it is not advisable as the printhead gets clogged easily. Kindly advise me further. Thanks
Bonsoir excusez mais la sincèrement je m'arrache les cheveux, La couleur ok Mais pas de blanc. J'essaye votre maintenance et les clips des petits réservoir d encres refuses d entrer .du coup les petits réservoir ne sont plus dans leur alignement parfait
Bonjour, ne vous inquiétez pas. C'est probablement parce que l'encre s'est solidifiée et c'est pour cela qu'ils ne rentrent pas. Je recommande de les remplacer et de nettoyer (flushing) la tête d'impression. J'espère que cela résoudra votre problème.
@@brildoren7440 thank you for the advice. I continued cleaning, hypercleaning, but it didn't work. As a last resort, I stuck a syringe in the waste ink hose to remove the air. that solved it thank you.
Hello Bryce. That's because the original video is in Spanish so what you can listen to is the English translation/voice over of it. If you only want to watch the original video, you should then go to Brildor's main channel.
thanks for the video.) tell me please, did you use acrorip v10? The problem is that the white ink shifts towards the end of the image and part of the drawing remains without a white substrate. Especially if multiple image and single print job
Thank you Any! We don't use acrorip v10 we use cadlink digital factory dtf edition but this is a white layer shrinkage problem. Maybe you have too many shrinkage pixels. You should go to the White tab and under Decrease set less pixels than you have. Maybe 1 or 2 pixels is enough.
Hi, i have a problem with my magenta color, it has black color in it, all colors are okay except colors that needs magenta. Magenta damper has black on it so it was contaminated, so what i did is to replace my magenta damper but the issue is still the same, my magenta colors has black color mixed with it.
Hi! I would suggest changing the damper first, but you should flush the printhead before replacing it. You should also clean the wiper blade and the capping station (the area where the printhead rests, which can be very dirty and, due to the negative pressure, the printhead absorbs discarded ink and contaminates the damper ink).
Hello, updated from my last question. I have a new machine Epson SP1390. After printed 5 sheets of A3, suddenly the initialising getting slow. It took about 25minutes on the first initialising then pop up error. Tried reset the spooler but still doesn’t fix. Get more space on C drive but still problem. Any solution? Thank you.
Hello Jacky! What software do you use to print? Have you tried uninstalling the drivers and reinstalling them? Have you tried changing the cable or the USB port?
@@brildoren7440 Hi, thank you so much. I will try to change the epson sp1390 driver. Or maybe you have recommendation for that software? Give link please. Thank you.
😢I have a converted Epson ET 8550 printer and I have had nothing but problems with this RIP software. Repeated paper jams and other issues only happen when printing from this Rip software.
I found your video superb! I wonder if you agree that I will copy your video and put my Japanese superimpose or after recording in Japanese language for re-uploading on to the You Tube for my Japanese clients. Please advise. Thank you for your consideration.
Hello Hiroshi! Thank you so much for your comment! I really appreciate it. As long as you reference or mention the original video, there should be no problem.
Hello! This may be because the usb ports are set to save power. You should disable the power saving options to ensure the flow of information. Another option could be a faulty usb cable. You can try on another PC to check if it is a printer or a PC fault. You can also contact Cadlink support and explain your problem. Hope this helps!
My DTF EPSON L1800 will start printing well and then just stop laying down white. Sometimes I will get a full 13x19 film printed and when I start next sheet the white stops. Sometimes in the middle of printing the white just stops. Any suggestions?
