On our how to channel, we show you how versatile LEISTER tools weld #thermoplastics. We show our #ProcessHeat hot air modules and introduce you to our #LaserPlasticWelding installations.
In our tutorials, you will find easy-to-follow, step-by-step instructions on the most important aspects of #welding. We hope our tips and tricks will allow you to achieve optimal results and allow you to use LEISTER’s line of tools according to your needs.
Dear Aaron It is recommended that the screwdriver or tear needle can penetrate 0.5 to 1mm without much resistance Best regards Best regards Your Leister Team
Buenas tardes, disculpa en el minuto 17:43 tienes activado en la pantalla del controlador CSS una bandera que dice "OUT 1", pasan los segundos, se corta vídeo, y ya no aparece, cómo fue posible que lo quitaran? Queremos realizar lo mismo que el vídeo pero no responde la pistola al controlador, no logramos nada, no detecta nada, espero puedan ayudar, gracias!
Dear Ricardo Out 1 is Alarm 1, which lights up when the value is exceeded. In the video, a value that was too low was probably first stored and then changed. That is why it went out. Best regards Your Leister Team
Dear Customer Our products must meet worldwide global standards. Among other things, the product is guaranteed. The individuality of the batteries can also result in price differences. Our products are delivered with a professional battery from Bosch GBA 18V PROFESSIONAL. We hope that you will choose a professional solution. Best regards Leister Team.
Dear Customer Thank you for your input. We need a constant negative pressure for our test method. We can only ensure this with a running pump. Best regards Leister Team
Dear Customer yes of course but it always depends on material/product/expirience but the machine gives you maximum flexibitly to adjust to your needs. Best regards your Leister Team
Můžete mi laskavě ukázat jak s tím vyvaříte vnitřní roh? Když v popisku uvádíte, že s tím vnitřní roh zavaříte? Botka v rohu nedosáhne na stěny materiálu!
Dear Customer How to weld inside corners with an extrusion welder can be seen in the following video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-4S4NnqThFl8.htmlfeature=shared Best regards Leister Team
Thank you for your interest in our product. For a price inquiry please contact your local distributor. He will gladly help you. You can find your distributor under the following link. leister.link/ynr Link to the UNIDRIVE 500: www.leister.com/en/product/Unidrive-500/163-144 Best regards your Leister Team
Dear Customer Thank you for your request. We have used the Heyboat mare 850 (H2562) from Heytex. Linkt to the product: www.leister.com/de/product/SEAMTEK-W-900-AT Best regards Your Leister Team
Thank you for your interest in our product. For a price inquiry please contact your local distributor. He will gladly help you. You can find your distributor under the following link. leister.link/ynr Link to the UNIPLAN 500: www.leister.com/en/product/Uniplan-500 Link to the UNIPLAN 300: www.leister.com/en/product/Uniplan-300 Best regards Your Leister Team
Dear Alex Steel roller are for GEO Civil Engineering applications. Silicone for roofs. More pressure can be exerted with the steel rollers, e.g. for HDPE waterproofing membranes. www.leister.com/en/product/Unidrive-500 Best regards your Leister Team
Dear Customer Thank you for your request. We recommend operating the PENWELD with hose lengths of 4 m and 8 m with the AIRSTREAM 100, AIRSTREAM ST, ROBUST or compressed air. These air sources provide the necessary pressure to overcome the resistance of such long hose configurations. The MINOR has too little air pressure to do this. Best regards your Leister Team
Dear Customer The WELDPLAST extruders from LEISTER give an automatic release as soon as the device has heated up sufficiently. This may vary depending on the ambient temperature. We generally recommend allowing 10 minutes for the appliance to heat up sufficiently. More detailed information can be found in the manual: www.leister.com/en/product/Weldplast-S2#Downloads Link to the products: www.leister.com/en/Extrusion-Welders#tab=LTAG-ExtrusionWeldersTabLeister Your Leister Team
Hello Silvio Thank you for your interest in our product. For a price inquiry please contact your local distributor. He will gladly help you. You can find your distributor under the following link. leister.link/ynr Link to the FUSION 1: www.leister.com/en/product/Fusion-1 Best regards your Leister Team
Hello Thank you for your interest in our product. For a price inquiry please contact your local distributor. He will gladly help you. You can find your distributor under the following link. leister.link/ynr Link to the FUSION 1: www.leister.com/en/product/Fusion-1 Best regards Your Leister Team
Hi Virandy, The Hemtek is a specialized machine for hem production. However, it is also possible to make overlap welds and join 2 fleeces with a special guide. Link to the HEMTEK ST: www.leister.com/en/product/Hemtek-ST Link to the special guide: www.leister.com/en/product/Hemtek-ST#Accessories Regards, Leister Technologies
Yes this tool can be used for PVC-U welding. Depending on what application you have, we have other devices in our range that may fit even better. Please also visit our website: www.leister.com/en/Heat-Guns#tab=LTAG-HeatGunsTabLeister Best regards Your Leister Team
The KSR Digital Controller and the DSE is phased out and not longer available. This components are replaced with the CSS (123.039) or CSS Easy (125.944) and SSR (159.220). They are much cheaper. Anyway, if you want to connect the old KSR controller with the DSE then you have to connect the port nr. 11 from the KSR to the blue wire from the DSE. And port Nr. 12 from the KSR to the red wire of the DSE. I hope we could answer your question in this way. Best regards Leister Team
We would like to offer you a training. We are convinced that with the right handling you can achieve very good results. How can we contact you for training?
We would like to offer you a training. We are convinced that with the right handling you can achieve very good results. How can we contact you for training?
Dear Ionel Thank you for your request. Press the Off button on the display and let the extruder cool down for 5 minutes. The air should drop below 100 degrees Celsius. The plastic remains very warm for a long time. But this is no problem, just don’t storage in the plastic case as long as its hot. Best regards Your Leister Team
Dear Mr. Shulman. With the right handling of the UNIDRIVE 500 do we achieve very good results. Let's make an appointment so that we can demonstrate the device to you. Please come with your coordinates so we can make arrangements.
With the correct operation of the UNIDRIVE 500 very good results are obtained. Let us make a device demo at your place, so that we can solve your problems. Please come with your coordinates so that we can make an agreement.
Hi Tom Please contact the official Leister sales & service partner in your country. There you'll receive the correct service / information for your FUSION 1. Sales and Service Points - Where to buy Leister Tools and Welders www.leister.com/en/Services/Sales-and-Service-Points Best regards Leister Team
@@leister-tutorials it’s ok, I figured it out. I had to hold the start button in and plug it on, then switch it on/off 5 times and it took me to the menu where I can reset the hours. IMO this is very shady tac tics to make your customers send the guns back to have the hours reset. And the fact the the gun shuts off completely making it unusable just because it hit the service hour mark. Not great Leister. Not great at all!!!
@@togwilson Dear Tom Sorry for the inconvenience. The extrusion welder must be opened to change the carbon brushes. Some safety-relevant points must be observed. For legal reasons, we cannot solve this in any other way. Therefore, we ask you to contact our partner directly. Depending on the situation in your country, you can carry out certain service and maintenance work yourself. Best regards Leister Team
Hi, The table and the welding space should be lower so that operator could work while sitting comfortably. Moreover, table and bottom wheel holder of puller should be mounted with use of quick coupling to transform the machine without extra tools.
Hi Marc Thanks for the input, we will be happy to discuss this with our technicians and make any adjustments in the future if possible. We are constantly striving to listen to our customers and improve our Leister products. Best regards Leister Team
Hello Moh Thank you for your interest in our product. For a price inquiry please contact your local distributor. He will gladly help you. You can find your distributor under the following link. leister.link/ynr Link to the SEAMTEK 900W AT: www.leister.com/en/product/SEAMTEK-W-900-AT Best regards your Leister Team
I want to control the Air Flow AND the Temperature independently via an external controller. Is this possible? I'm using an Omron CJ2M PLC and a 0-10 V Analog Output card.
Yes, you can control the air flow and the temperature via an external controller (4-20mA or 0-10V). But you need one controller for the air flow and one controller for the temperature. And you need also for both 24VDC power supply. You can find more information on our homepage. www.leister.com Best regard Leister Team
