Don't like the ledge that was formed on the abutment wall when timber was fixed, the joint between the roof and wall is always a week point for leaks with driving rain, especially with a small ledge wher water can sit
Lots of punch list items here: Edge metal improperly installed, Joints should be overlapped minimum 3”, Not butted together. All sheet metal must be removed and re-installed correctly.
Single ply metal needs 4mm gap between them,150mm joint strips with a 50mm unbonded part in the middle.to allow for thermal expansion.Ive done 100s of thousands of square meters of Single ply since it started in the late 80s,Alkor,Alwitra,Sarnafil etc,and i can tell if a cowboy has done a roof, by looking at butted,or lapped metal,and fully welded join strips.
@@mr.145 that only applies if using PVC or TPO coated metal then you heat weld to it. I’ve done 1000x roofs and know before I even go on the roof if it’s done by an alley roofer just from a phone call.
@@ryanjarvis9675 The manufacturers told the suppliers that. Incidentally ,I just replaced a single ply roof with a 3 layer torch on system. the decking had rotted in many places and needed replacing.. The single ply had been cut as well.
@@MrFlatroofer yeah the only problem with single ply is that it’s a singular layer and if there is a minor weld left open the water will go straight through to the deck. However the best way is to have a torch on layer as a vapour control layer then Insulation with a fully adhered single ply system direct to the TR27
Today I’m 17 but when I was 15, me and my dad went to a farmer boys restaurant to instal all that single ply. I don’t know much but I assure you all that, that’s the most delicate and detailed job I ever faced. Good thing my dads a 25+ year experienced roofer and has done almost 50 single ply projects.
I’ve spent spent 25 years surveying & repairing buildings. Single membrane, mmmmmm leaks, leaks, & more leaks. All these jobs I refer to, were commercial & carried out by approved contractors. In the video, I’ll wager water penetrates the upstand to the stone wall in around 8 years or so depending if it’s west facing. Building materials move differently, especially mortar along that length. Also, come the day day when you fall of a roof........well, put it to the test; jump of a roof in a very controlled way & see if your body hurts.... It hurts. I know from falls & bitter experience from days, long gone.
Gentleman at least its not just flat with a epdm on it like I got ...........which was flooded and ponding after a rain..this one is not flat..at least i believe there are crickets,or raised wooden panels from what i can see..my job for a 27x13 ft flat roof was 8000.00 no rafters,so dont be so critical!
I was fearing for the bloke walking backwards as he was unrolling. Health and Safety aside, that's a very dangerous practice with no scaffold up there.
Some really awful practices here. I am aware that HSE have made convictions using evidence from RU-vid. I would remove this. No edge protection, no PPE, no safety at all.
Ive fitted thousands of m2 of singleply over the past 15 years, and if 1 of my lads ever walked away thinking that was acceptable, they wouldnt do another job for me! Direction off lap falls doesnt matter, not important. But even tho its not required, get the sheet down before the edge trims, clamp the sheet down. Upstand is a mess...i wont allow a single ripple anywhere. But those standing seams!!! Why he hasnt measured out so they meet on the hip is beyond me and why hasnt he used a straight edge to work to, keeping them straight. I could drive a straighter line, pissed!
Okay, on the lapping comments, once they're welded, they become seamless. You can literally put the laps in reverse and they still wouldn't leak. Personally, the only thing I wouldn't have done was to tie the roof into the wall at the flashing point. I just see that flashing buckling over time and pulling apart, but I could be wrong. Maybe it worked. The physics however dictate a free tie in there where the roof can move independently from the wall and still be watertight. However, having said all that, I can appreciate the metal roof look on a more traditional structure. Well done gentlemen. While in my personal opinion, architectural shingles with ice & water shield underlayment would've done well there for a few decade needing practically no maintenance and it would've been pleasing aesthetically, the job looks really nice. Slate or tile or copper standing seam would've been the ultimate of course, but this roof probably came in at 1/3 the cost. Again, looks great. Good stuff.
Guys all talking shit about there laping yes I think every roofer knows about lapping these guys obviously have done roofing they're not idiots I've never done vinyl from what I hear its the new way to go lasts forever so obviously these guys know something that we don't know about lapping vinyl I think it was a clean job and that's amazing that you don't have to worry about putting a seam any direction clean job boys do you have to go to a class to get certified to install vinyl I would like to learn that all I know is shingles tile and hot mopping buy vinyl is the future from what I'm told great job though came out so clean
Running the seams the way they did is fine .Water is not hitting the lap edge which could be an issue. Hot air weld is very good if done properly. All in all a good job. Wonder if they scaffold bottem edge to prevent falling all the way to ground
as a PVC man i'll try to avoid laying against the fall also normally you will do all preparations before laying the membrane and the drip flashing we will fix over the flees backed membrane it will require strap anyway
i would have started from both sides working upwards to avoid any type of water penetration on seams, can almost guarantee leaks at the hips where you will have a hard time hand welding 2 different angles.
5 times longer to install than a felt or grp roof so its pointless and roofers without ppe and scaffolding are uninsured roofers who you wouldn't want working on your own house
it looks like a unreinforced fully adhered single-ply. as long as the seams don't buck water it's ok. looks like they did a fine job. nothing ive seen in the usa, but they've brother roofers. give them a break.
If water gets to those screws its gunna leak and Should of used auto welder on seams instead of using heat gun all across because i know for a fact there is an opening that wasn't welded right. Just saying
What H and S. Must be the rarely seen bouncing roofers that dont need fall protection. The works substandard as well,stick with private jobs where they know no better. TBH it gives roofers a bad name just by having no fall protection,and to make a vid showing it???
Fall protection? You are joking right? It is a flat roof, why would you ever need fall protection? Looked like a good job to me. Fall protection is up to the induvidual, and weather he feels safe with, or without it. when you use it, where it is not needed, it causes accidents, not to mention getting tangled in hoses, cords, and all other crap. Laws requiring fall protection, were put in by statists, who wanted more man hours for the big union shops. I have been roofing well over 25 years, steep slope residential, mostly, and have rarely worn fall protection, only when I thought it was needed, or when I was in a highly visable area, and risked getting a fine. I have NEVER fallen off a roof. For the past 8 years I have been in buisness for myself, and am not requierd by law to follow any of the nanny state bullshit.I can't beleive a roofer would say it was bad to have a video without ropes on, and that made roofers look bad. Of all the things roofers do. Have a nice day.
Its not a choice its a legal obligation.My uncle Maurice worked as a roofer for 30yrs and fell off only once.Your attitude(only when I might be seen) is all thats bad with the industry,I dont really care about you being in a wheelchair or dead but the poor sods that work with you,your attitude to health and safety stinks and epitomises the smart assed attitude that caused so many men to be injured and killed falling from heights. Fall protection as a employer is your job,you leave yourself open to charges of corporate manslaughter(someone done in Sheffield 2 yrs ago,fined and imprisoned after a man working for him fell through a skylite). Thinking HS doesnt apply to you as you are so clever/good that you wont fall is beyond all stupidity and arrogance,no-one thinks theyll fall but most have the sense that they might so look after themselves. Have a nice day yourself,dont fall,your insurance wont pay out and if a employee falls youll be hopefully in prison,or have a bit of common and some HS.
I am sorry, but it is not arrogance, it is me taking responsibility for my self, and making my own decision. I use my fall protection when I feel itt is neccesary. What happened to your uncle is terrible, but people have strokes when they get up to fast. Roofing is dangerous, and if you feel that you are safe, and connfident, who is a politician to tell you otherwise? Did your uncle fall off a flat roof?
Probably the roofers trying to make a living where there is virtually zero regulation and pricing in scaffold on single-storey residential is pricing yourself out of the job! If everyone did it then fine but that’s not the case and not everyone has the luxury of clients with a budget to have works undertaken by the book. Ethics aside, that’s the reality for most residential/small-sized roofing businesses.
The membrane doesn't have a lap it has a welded seam and the orientation of the laps doesn't matter as they will accept water flow against them. The issue with posting video's like this is the lack of edge protection which is a legal requirement demonstrating the lack of care from the roofing contractor ! Professionals or amateurs ???
Bowing down to the state does not have anything to do with professional, or amuature. the finished job, customer service, cleanliness, during, and after the job, and pride are some of important aspects of a professional. Not your ability to take orders from someone who has never been in your situation, but thinks they know what is best for you. Like they care about your safety more than you. When did men stop being men, and become such jack boot lickers. Sickening. As for me, I will continue living free till my last breath, and will take orders, nor ask permission from no man. Have a nice evening.
I'm one of the boys in the video and you point out the way the laps run (so your a felter lol) you don't know what you're talking about as single ply laps can run anyway and hammer screws ? Called hammer fixing Google it you learn something new everyday just you learn more as you know nothing
my dad did built up felt flat roofing for over 50 years .all types of roofing .we was one of the 1st to use this system when it 1st came out .I been roofing all my life as well .and I can tell you this much you always and I repeat always start at the Lowest point of the roof .any roofer in the world will tell you that /roofing people will just laugh if you try and tell them the right way is the way your doing it .because it just is not .
Do not comment on something you know nothing about . as a member of SPRA i do Know what im talking about and it doesnt matter where you start with single ply. with felt you always have water shedding laps but with SP you can have either water shedding or water collecting as the welded lap is the strongest part of the membrane unlike Felt which is the weakest part. and for your information i am an award winning installer of both and have also featured on Grand Design and my company installs roofs of up to 50,000m2 annually.
