Thank You So Much For 900+ Subscribers. You are the best audience.
Welcome To Nirosha Rc. I am from Sri Lanka. I hope you'll enjoy my videos. Feel free to share them with others. Subscribe, Like, Share with your friends. And Stay with our Channel For a new experience with Rc cars!!
Saya pake reciver dumbo rc yg 10 channel gak bisa gan, cuma nyala lampu kota aja, tapi kalau pake yg 6 channel fungsi normal, Bisa dibantu gan, problemnya dimana ya
Bro, Motor ekata dala thiyana male bullet connectors koheda ganda thiyenne? mage hobbywing 1060 esc eka 370 motor ekata connect karaganda widihak ne. XT60 connector ekak motor ekatath use karanda puluwanda?
@@nirosharc Hi there ! I have seen that many RC users just connect the LED lights for their RC without resistor (typically 3V).. while some add resistors. What do you recommend ? Appreciate you valued reply. Thanks
@@newtonsmeter6239Hi, LEDs are designed to operate within a specific voltage and current range. If you connect them directly to a power source without a resistor, they can draw more current than they’re designed to handle, which can lead to overheating and eventual failure. Adding a resistor is a safer and more reliable practice to ensure that your LEDs function correctly and have a longer lifespan, Thank you.
@@nirosharc The LED controller as in the video has 2 output poles, positive and negative. I want to use 1 positive and negative pole for 8 LED lights. and I use 1 positive pole and another negative pole for 7 LED lights. and I installed all the lights in parallel. Can I just use 2 resistors?
@@GarengPetruk I asked Chatgpt and it answered me like this:- Yes, you can use two resistors in this setup. One resistor for the 8 LEDs connected in parallel to the positive and negative poles, and another resistor for the 7 LEDs connected in parallel to the other positive and negative poles. Make sure to calculate the appropriate resistor values based on the forward voltage and current specifications of your LEDs to ensure they operate within their safe parameters.
@@nirosharc OK, I'll try it. Previously I used it without a resistor with 2 2 watt HPL lamps and 2 1 watt HPL lamps. Combined with standard LED lights, MN99s RC lights. and it turns on but after 4 days of me using it. My controller immediately caught fire. My controller is the same as yours.
O seu controle remtor tem o ch4 de 3 estagios (frente / parado / reverso). O meu controle remoto o ch3 e ch4 funciona só como liga e desliga, preciso de um switch que inverta a polaridade do guincho. Voce sabera indicar um no Aliexpress?
INJORA RC Car Winch CH3 Control Line:- s.click.aliexpress.com/e/_DloWgT5 AXSPEED Simulation Electric Winch Control Wireless:- s.click.aliexpress.com/e/_Dd3iZ95
•Connect the two wires of the motor to the two yellow and blue wires of the esc. •You can watch it in the 4:30 minute of the video below. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-VejCuznBj3s.htmlfeature=shared
Man I've been adjusting the axles on my MN82, those things have such poor tolerances, I had to make shims out of solid copper wire, AWG 18 and 22, I think I'm going to order bunch of shims and redo it all, also had wrong sized bearings, press fit bearings that sits very losely (poor machining or interference fitting vs not) the knuckles axles are also not square and binds! Gonna order some spare ones and hope they are straight...
It is the wire of the lights I made. Does direct current from the receiver to the light bar work? 1. Change the side of the wire clip and fix it. 2. Connect to another channel (ch4,ch5,ch6) 3. Check that both the transmitter and receiver are working properly.
