@@kalaabamdivine8204 brother U phase ampere sense agala internal (CT coil) problem,may be moisture agi CT terminal S1,S2 l short agi irukkalam, switch off and clean use electrical spray, otherwise CT damage change with service person

You want VFD?

@Valssssz, telegram call

Power card problem,change Power card

@Valssssz telegram call

Bro maximum frequency, maximum reference, maximum output frequency,3 check pannunga,then current limit check, reached current limit frequency automatically down

5.40 set 0( no function) , normally one relay for ready comments one relay for alarm comments,

Thampi telegram vanga I'd @Valssssz

Ok anna

6.3.1 la 1 vacha store set , then remove other drive fit and 6.3.1 la 3 vacha set agum,5 vacha factory default settings

Same range drive have?just interchange control card after check may be control card problem,not keypad problem

உங்ககிட்ட இதோட டிரைவ் அட்ஜஸ்ட்மென்ட் மேனுவல் இருக்கா

This drive we using in escalator

அந்த மதர்போர்டு சேஞ்ச் பண்ணி போட்டா ஓடுது

பட் அந்த நியூ டிரைவ்ல உள்ள அந்த சேம் போர்டு வேலை செய்யாதா

2.13 (RY1)you put 22,if you take run command,you can select MO1(2.16)use or M02(2.17)22 for over current stall protection

Fc360?

FC-280 brother

3.03 first check pannunga maximum reference

4.14,then 4.19 maximum output frequency change

Bro plc control panel trouble shooting panna ,first input output program eppadi panni irukkunu therincha pothum, particular input varalana,athukkulla output on agathu,ithuthan matter,each and every PLC DIFFERENT PROGRAMMING

Brother namakku delta PLC simple ah ladder circuit program padikkalam, konjam tight work schedule, niraya vfd video pending irukku(ABB,yaskwava,sew) konjam time agum ellam pannalam

Boss this is my profession last 15 years,this videos, youtube Idea all of my juniors request and suggestions

Better ,you can try each drive settings seperately ,my company have lot of models vfd,am also spend more time for settings after that prepare videos

@Valssssz come telegram

Visakhapatnam

@@valsonvasanth9233 ji, iam working in Dubai, can youhelp if any doubt in my company project about Vfd , how can I contact you ?

No brother you say 0.5 hp price

Next part will be soon (own program with delta make works going on)

Brother cd 1 u phase current CT sense ஆகவில்லை (internal problem) Factory reset,dust and moisture clean(wd40 spray use,power off condition) இது மட்டும் பண்ணி பாருங்க, Current Transformer terminal moisture la short ஆனாலும் sense ஆகாது ,இதுல சரி ஆகவில்லை என்றால் service தான் (authorised service person) possible

@@valsonvasanth9233 Thank you sir, but second board (capacitors) yeppadi remove panrathu, theres no screw or lock holding but its very hard to pull out to access CT & igbt board..

Jog speed 100% maximum Hertz, உங்களுக்கு எவ்வளவு தேவையோ அதை வைக்கலாம்,crane application,light rotating equipment than ithu, acceleration (ramp up)time based than immediate ah full speed reach pannum , jogging

Fc 360 drive jogging speed up 0 to 400 hz and acceleration time will user programmable

Start failed error ,hand mode la try pannuningala?,hand mode de activate panni vacha appadi than kaatum,0.40 hand on lcp put 1,hand mode work, saftey swich not working (I/o terminal not working) careful conveyor application

Vfd ms 300 program 3.11 gain 100 இதை கம்மி பன்றது போல்.donfoss drive லவ் எப்படி செய்வது program சொல்லுங்கள்

RTD resistance temperature detector (only low temperature max 400 degrees available in market after that we are going thermocouple)

Welcome

Come telegram @Valssssz

Come telegram @Valssssz

புதுசா முயற்சி பண்ணியது plant near by running, அடுத்த முறை சரி பண்ணுறேன்

பண்ணமுடியாது, ஆனால் 5 hp drive la 2 hp 2 phase la run agum,otherwise 2 phase to 3 phase choke type transforme in input side

Special edition VFD available contact delta supplier