salve ...complimenti per il magnifico lavoro...Le chiedo dove ha acquistato le parti per il cassone in lamiera e le parti della carrozzeria della macchina?
Blackhound Optics is doing a big labor day sale! 40% off all regularly priced products plus you can stack the affiliate discount of 15% off for a total of 55% off! that's a smoking deal! The coupon code is "hesty32" and here is the website link: www.blackhoundoptics.com Don't forget to put what rifle you are mounting it on in the comments so you get the correct rings. Sale is active 08/30/2024 8:00am - 09/08/2024 11:59pm
Blackhound Optics is doing a big labor day sale! 40% off all regularly priced products plus you can stack the affiliate discount of 15% off for a total of 55% off! that's a smoking deal! The coupon code is "hesty32" and here is the website link: www.blackhoundoptics.com Don't forget to put what rifle you are mounting it on in the comments so you get the correct rings. Sale is active 08/30/2024 8:00am - 09/08/2024 11:59pm
Blackhound Optics is doing a big labor day sale! 40% off all regularly priced products plus you can stack the affiliate discount of 15% off for a total of 55% off! that's a smoking deal! The coupon code is "hesty32" and here is the website link: www.blackhoundoptics.com Don't forget to put what rifle you are mounting it on in the comments so you get the correct rings. Sale is active 08/30/2024 8:00am - 09/08/2024 11:59pm
Hi I already purchased a swapped mk4 1.8t jetta. the previous owner did not do the brake light / cruise control / clutch switch. would this video still work by just skipping the starter and vss?
well sort of. Yes but you still probably want to do the procedure for the starter relay so that you have easy access to the wiring for the clutch switch. The cruise control is pretty much its own procedure
Sir. I dreaded doing this for a few years and spent just an entire Sunday morning yesterday. followed everything to the T and everything works exactly as it should. watched this video about 20+ times to get it in my head. EVERYTHING works as it should and it has taken a huge weight off my shoulders. now onto your other videos to finish my project. THANK YOU SO MUCH
question: If i am installing solar into an Rv with existing electrical. It has Generator and Shore already. I should assume it has a transfer switch to manage this. Now If I want to add an inverter ran off batteries... is the solution to add ANOTHER transfer switch? therefore the shore/gen gets sorted first and then feeds the subsequent transfer switch. I want to default with solar inverter but have the option of shore/gen. thanks in advance if you can respond.
Pretty sure you want your solar to go straight to batteries (well with a solar controller/converter) when you run off solar you are actually running off batteries to protect the panels from overdraw. Not super knowledgable on the actual workings there though
Just reread your question and yes I believe you can either swap to a 3 way transfer switch or add another 2 way up stream to in effect get a 3 power option
I followed the instructions to a tee, used the same hardware and drill bit he used and had the window crank fixed in 5 minutes- thx so much for this video!
I got one of these Android units for a 2010 Beetle, but the reverse cam screen does not come on when putting it to reverse. How to wire the reverse camera?
Can you show how to fix a window crank that’s been “over cranked” the wrong way? It still opens and closes, but it doesn’t close tight like it used to.
Thank you for this video; very helpful. I experienced the foam coming through all the vents on my 2003 Jetta so I knew I had a blend door issue. I went to the dealer who gave me a $4,000 quote to do the job with no guarantee that it would work or that they may break some parts during the process. Even though the car is in perfect condition even after 21 years and 74k miles, the cost to repair would be greater than the value. I decided to do the project myself. It took about 15 hours from start to finish. I took pictures of everything and labelled every screw. Every part was laid out on a sheet of plywood and documented. The hardest part was extracting the black box in front of the blend doors; had to remove the 13mm bolts to get the added room to wiggle it out. For the blend doors, I used the heavy duty end foil tape with the plastic backing - wrapping the blend doors was surprisingly easy. Putting it back together was just as tedious to ensure that the trim gaps all lined up. The two screws to secure the black box could not be reinstalled; I could not get access as easily but I made sure the box was in there snug with the clips. One thing to watch out for is where the radio harness comes out - if you lay it on top of the bracket divider it will not be long enough; make sure it is below the divider. Once completed I had no screws left over and everything looked good. Despite the fact that I had removed a lot of foam during the dismantle, when I tested the system more foam came out until the vents cleared out from any remaining pieces. After that I tested all the baffles doors using both AC and heat and directing airflow from various vents. It all worked perfectly. This job requires patience, a slow pace so you don’t break anything and documentation; don’t rely on your memory as to where stuff goes.
Great video....thanks a whole lot. Mine is a Thor. It has a spacer between the two rollers on the window track that has to be installed also. You saved me a ton of work.
On one of my savage magazine. The rear catch broke off (strange but just sheet metal) I epoxied a 1/8 thick piece of steel about 1/4x1:4 and it is working well. But if you are talking about the front catch/release, I don’t have a good fix for you
I’m assuming you have an 09A auto so then you should watch the 09A tiptronic series instead to see the VSS wiring. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ncKRdmGXfsQ.htmlsi=Vva8a5Cl9LO3PTuk
Когда то и я мечтал о том, что буду строить пикапы. Может уже настало время? Думаю начинать и в 60 лет не поздно, хотя и с полного нуля. Я в Рязанской области в поле поставлю навес для начала и начну воплощать мечту в реальность. Поддержите добрым словом все неравнодушные! Прекрасная творческая работа. Здоровья и новых пикапов(особенно жду проэкт пикапа из WV MK2)!!!
I just bought the Axis ll stainless steel in 308 from Walmart and am researching for 10 round mags, I see in another thread you found someone who's makeing these that don't cost an arm and a long.... and that you were going to post a review.... So what ever became of this ?
What is the purpose of the foam to start with🤔, if you already know they will degrade with time? Is this a manufacturing design issue? Just wondering. Thanks for sharing the tips and tricks to solve the issue. Now I know,where the foam pieces are coming from🤯.❤👍👍
I just bought the Axis ll stainless steel in 308 from Walmart on clearance... Am researching 10 round mags for it.... So far all I see is conversion kits.... plus $160 mags if you can find them in stock... That's to much money.. Have you found anything ?