Wah mantap terima kasih ilmunya bang

JESUS CRISTO te amo muito ❤

4 estrias y 4 campos?

Finally someone who knows how to treat his tools well (with cutting oil) ! Interesting video !

ну вот глушак и готов

Un boulon rayé au pas de ? pas tout à fait un canon mais presque. En France ça deviendrait une détention illégale de boulon à feu probablement de catégorie B vu que trop court 😁

How can i order of your amazing pcp

Tüfek namlusu namlu tüfeği değil

Звичайна прошивка. Хоча ні! За таке виконання та ...кхм... прости Боже... якість, треба йому руки ламати та на норм зрощувати...

The state can never ban our knowledge.

I used something similar many years ago and if my memory serves me correctly it was a commercially made tool very similar to the one you made. The only difference was that the bearing race ran directly against the workpiece rather than a single loose ball that you have. I found that it worked better if it was running slightly angled rather than square on in order to allow the radius at the edge of the bearing to exert more pressure.

Mantap,,, Joss

You are very artistic man. I watch all your videos with interest.

Nice but that is not a barrel.

How to order

Obviously I subscribed immediately. Thanks dude, I can't wait to see more of your videos.

Safety sandals deployed

Maybe some English grammar it’s taught not teached

Well done I think you should make many and fit magnum rounds in them to get better protection 🎉

Сделать можно многое. Только вопрос зачем? Что бы получить уголовный срок за изготовление деталей к огнестрельному оружию!

Tüfek namlusudur o

That's a neat burnishing tool.... must make myself one.. 🙂

Apakah ini dari shop motor

U Are very lie drill hole is true but after that were fake Steel bolt rod is harden why u lath it by hammer hand I ever seen other lath rifle barrel .They not do as U

Get a better centered bit when you tighten the chuck using all three of the holes with the key but pretty cool project yup

Minute of barn accuracy

Itu gear nya pake gear apa bos

What in the world would you do if that drill bit welded to a screwdriver shaft broke off with it half way in the bolt? Get a new bolt and start over?

wrong type of locking ring

Flip flops in the shop? Why arent you wearing steel toes? Are you promoting unsafe work practices? This channel is bad news.

А теперь видео как сделать РСЗО из кислородных баллонов и водопроводных труб, пожалуйста

Alot of machinists coming from school cant operate a manual lathe . Thinking outside the box . Awsome work

Demi Tuhan.. Bahannya dari ancuran..

Cute

great job 👍👍👍

Вот так делают реплики калашей в юго-восточной азии, красава, респект.

😮Брехня. Это получается. Но только на координатно-фрезерном станке. 😂Не на коленках.

Info Lokasi nya di mana bengkel las bubut ini lord matur suwon

охренеть

Good Job!

Mantap mas bro !!! Slamat berkarya dan jangan lupa utamakan keslamatan. pokoke 👍👍

CAN I ORDER THIS FROM YOU ???, IF YES THEN HOW MUCH???....

muantap bang..

quando uno ci sa fare ,,ci si deve solo inchinare di fronte a tanta bravura complimenti dagli statiuniti

Desde Patagonia Argentina 🤠👍🏻

This is why all my zip guns were smooth bore.

Bravo!

От 5 до 15

Nice work. You have more "know how", in your little finger than all of the CO24 Harvard student poofs combined. молодец удачи!

respect. i worked as a turner for about 7 years and its really good to see your videos. 👍👍