Learn how to be more sustainable & resilient here at Enso Homestead.
After searching for 7 years, my wife and I found the 10 acre property of our dreams out in the woods of Western, WA. In 2015 we established Enso Homestead and 5 years later build our home during Covid. This is our journey.
I just found your channel and watched you make turkey tail tea. I pick mushrooms, I wear rubber gloves, I dry them , I never eat any they are too valuable. I breath their amazing molecules to stay healthy.
That was awesome 🎉 I had Service techs who wanted to charge over $200. Luckily I found one pair to at least fix the broken set. We got the same rig 2003. Make sure to work on your roof seals. I’m working on a video for that this particular era 2002 to 7 have a factory defect in the file on roofing and the buildup of moisture that causes delamination in your roof to get up there and check that out! great spring tip!
This was by far the best method, as long as the springs are facing the right way............. I did the shim thing for the rear springs to remove them and used the block and tackle method to put the new ones on, but for the front springs I had more room to work and I was able to use the block and tackle method for removal and installation. It was an all day job for me but it's done............ thanks man!!!
Simple as it gets. I cut a 6x6 block to fit my desired height. Cut some basic paracord to length. And screwed a Trax 5" screw low on the block towards the ground. Thank you very much for this video Enso! I am now able to change out a set of springs in 5 minutes. #SkipTheShims
I bought next Ruger American rifle in 2020 (but this time Ruger Predator ) 308 Win , and once again got a probems with magazine (this time not rotary but Flush fit ) I ask RUGER staff about conversion kit - got answear as with this SERIAL Number kit will not WORK ! I insisted to buy ! FINALLY yesterday , i have made ! and ..... works as HELL with MAGPUL 7,62x51 magazine ! Thanks ME !
I was trying to figure out a way to put a cheek riser on a Magpul AR stock for my daughter, and this looks like a great way to go! Thanks for sharing this idea.
@@mattlimmer9644 a 500 gallon propane tank is 37” in diameter and the bowl is about 18.5” deep. There is a weld band that I cut on so it is a true hemisphere.
Glad you finally called the magazine catch a mag release, hearing you call it a trigger was painful. That hammer...yikes! That hammer has no place near any firearms. Get a couple of the small sizes of ball peen hammers and a hammer made with firearms in mind that has interchangeable heads. (I have seen people use that jig successfully and I have seen people do the install without)
At the 1.55 mark you were putting the magazine clasp (you called it a trigger) into the jig BACKWARDS. See this video for correct use of jig: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-LP7hfsB7VUI.html Here is another vid showing how to use the jig: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-i1j8XyJZBdM.html
The problem is they won't keep long once harvested without dehydration and grinding into a fine powder. One could take the whole log home or buy a grow kit and harvest as needed, I'm not sure what the life cycle is tho...
When you have the new base bolted up, test fit the latch with an inserted magazine before you drive the pin. Each one will be different, and some may require a bit of creative file work.
I harvest some in Missouri last summer and now I know it’s the lookalike. I have been making tea out of it for a month.Well what does not kill you makes you stronger 🤪. Not sure at my age.