Hey, thank you, I'm with the Atom stack a20 pro. The setting for the $30 was on 255. As per your guide, It's now on 1000 and cuts like butter. Before this, it was so lame.
very good tutorial, I followed it, I shorted the electriciby of the full building (yet dont understand how I did it) but no its working nicely, so thank you!
Hi, do you know why I can't upload any other config file with changes using fluidterm as you do here 27:55 ? I have to erase all flash memory and install everything once again even when I did some little mistake in .yaml. Im getting Return -2.
@@brakthehun yeah, I've selected the right COM port. I installed and uploaded older version of FluidNC (3.5.0), the same you have used and I got rid of this issue. However, I'll use an Arduino Uno to finish the project as I am using standard ESP32 DEVKIT V1 and do not have MKS DLC32. I've tried to use TXS0108E level shifters to send the signal to DM542 stepper driver, but my stepper motors are going crazy, they didn't want to move even when they were supposed to, I've erased everything from ESP32 once again and uploaded some simple code to control only one motor (X gantry), just to move and be still. And guess what happend :D All motors (other Y and Z gantry) which were not supposed to move had worked as I described in code along with the specific one I've programmed and wanted to move. The stepper motors operation is unstable, I don't know what it can be, maybe it's my skill issue in soldering as I'm doing the project on a prototype board, or some ESP32 soft problems, or just bad hardware connection. Despite all of my issues, your guide helped me a lot during the process of setting up the firmware on ESP32, everything worked perfectly, I've even had an internet connection established :D
@@md.asrafulislam1436 go to the console and ask it. Type in $$ and hit enter. Register 30 ($30) will tell you the value to fire the laser at max power.
I abandoned ugs and went to lazergrbl same issue if I hit home it gives error code pin9 x limit pin10 y limit and pin 12 is torch on also can’t get it to come on
You are stupid because on the ESP32 board there are WIN and GND pins to which you connect +5v and ground you did not have to cut the socket. This has nothing to do with the professionalism you mention.
thank you so much man, i have been looking for a good starter video on how to use this software and your video is perfect. thank you soooo much man ill sub and keep a look out for more
Great tutorial 👌 Handy little tip... you can use a putty (here in AU we have Blu-Tack) to temporarily hold the board and wires while soldering. I use this trick all the time for electronics repairs and assembly
Hi, I have an atomstack s20 max. The power of the laser is 18-20w. They cannot cut plexiglass (acryl) 3 mm at all. Is the problem that the laser power is low, or did I not set good parameters for cutting? I use the lightburn program
The AtomStack S20 is a blue laser. Clear plexi does not absorb blue. It passes right through. To engrave / cut clear plexi - you will need a different laser. People usually use a CO2 laser because it is a far infrared beam. at that wavelength,, the acrylic completely absorbs the energy. Unlike blue that passes right through,, the plexi can't pass the IR and it absorbs the energy letting it engrave / cut.
Great video for GRBL But I have a little different setup looking for help arduino running separate drivers with ugs how would I connect switches I can’t find any advice on my setup
Thank you for your detailed tutorials ... helping me a lot as a beginner. If I had a wish to the LaserGRBL programmer ... I would like to have a second indicator for the actual laser power - just like the buffer "VU meter". This would help to utilize the full dynamic range of the laser power (instead of reading the actual Sxxx values while running).
The latest version of LaserGRBL has them by default but I have a video that shows you how to make them: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-wKgJeqJv_y8.html This was before they defaulted to have a perimeter button.
Thank you so much for the this! This is literally what I needed for the project, as coding noob, this was mighty helpful, keep on making these solid videos!
The centreing and framing buttons are grey in laserGRBL even when successfully connected to my atomstack. I have just set it up for the first time. Does anyone know why this might be?
