data recovery 1gb free -www.stellarinfo.com/windows-data-recovery-professional.php?gclid=CjwKCAiA_eb-BRB2EiwAGBnXXpU_ivs4o8UmsLFWXtgjig0UOK8bs3jn1kYTXMvTiK8IiEDKO6pfuRoCOmMQAvD_BwE
Resister color code calculator . www.digikey.ca/en/resources/conversion-calculators/conversion-calculator-resistor-color-code?General&PMax%20Shopping_Supplier_Bourns_0118_Co-op&General&productid=&Cj0KCQiA4NWrBhD-ARIsAFCKwWt9DYgyhN_6LWd3z7mWgVorzJR7g9WAgJUKILhJqXOgs8z6WJVhQM8aAnqNEALw_wcB&gad_source=1&gclid=Cj0KCQiA4NWrBhD-ARIsAFCKwWt9DYgyhN_6LWd3z7mWgVorzJR7g9WAgJUKILhJqXOgs8z6WJVhQM8aAnqNEALw_wcB
Tims Pizza is better than some Walmart specials I've had. Definitely better than Pizza Pizza cardboard! Still timmies pizza is not a winner. But not bad.
Hello I have yahama Rx v490 amplifier it has power supply problem when I open main electricity switch then a convert then amplifier but display wont comes it continues make sound of tik tak then I keep it sutt down for one month then it works properly for a week till it won't get any fluctuation of current supply
I’m happy to see someone else uses shielding! I use mu metal sheets cut to size and find it realy does help with interference from my other electronics. I also shield the power supply.
I’ve done this to my triple shunted controller and the results are really surprising. I didn’t just add a little solder though, I didn’t squeeze the shunts together either but fully bridged them with solder. My controller was rated at 45A apparently which I don’t believe as it was already slightly modded from the factory. Battery sag at stock was 3-4v but with the full shunt mod it’s up at 7-8v which I expected considering I’m almost doubling the amp draw. Battery has 50A BMS but will allow much higher for peak draw over a few seconds. At this point it’s difficult to keep the front end down on full throttle pull off, especially if the forks are compressed from braking. Gonna be fun when I upgrade to 72v 28ah rather than my 52v 20ah pack. Will sag less thanks to the extra 2 in parallel and top speed will be increased considerably. I will make a baby surron 😂
I'm using a Samsung a11 Bad phone really And just watched your vid I immediately got up and went to the next room still connected and the vid running, i didn't face a problem really, it got me through 10 meters away in another room very good with no delay or connection lost, though when i went further away it began to lose connection a little, and when i put my hand on it covering it it lost connection too but not dramatically And when i put the phone in my pocket i didn't face any problem at all So yeah, i think it differs, kind of a hit or miss with those cheap earbuds
The question is does the amp sound better with battery vs the smps? Using low power into sensitive speakers, how big of a battery does one need to listen for at least several hours?
Mine's buttons are pressing themselves? Particularly the auto oscillate. I hit stop oscillating on the remote and BEEP immediately it auto oscillates again. I press stop, BEEP it goes again. What exactly is the problem? I opened the top and not sure if I see any problem. What exactly is wrong with it? It's so annoying that it beeps beeps beeps every second switching from oscillate and steady over and over again without anyone pressing anything.
Hello! Would love to see any update on this camera. My father-in-law gifted me this camera that he used while his stint in the Korean War. Has to go through a complete CLR... any chance of service/.parts manual out there, or anyone that may service it? THANKS!
@@KarmaElectronics. Thanks! Still working on mine. Would love to see the Bulb and shutter speed adjustment, specifically. All other stuff, including rangefinder adjustment, done by myself after watching some nice informative videos and pages.
hope u didn't charge someone money just to swab the switch with isopropyl.... i thought you were gonna remove the switches, and stabilizers and do a full teardown and cleanup.
Tengo una lg f1 express dual andatodo pero cuando esta iniciando windows 7 se apaga la pantalla pero las luces siguen ensendidas ...que pueso hacer????