I’ve tried turning the two adjusters and also using a swab to get any debris of the laser itself, is there any certain way I need to turn the two adjusters?
Bootsowen has a Hotpoint WM54 fully working he found on the street. All that's wrong with it is that it is rusty on the front. I believe he's based in Manchester but he doesn't want or need the machine. If you wanted too and were close enough, you can take it off him for free, just email him or leave a comment in one of this latest videos and he will give it to you! Just saying incase anybody wants it or else it will be scrapped! Would make a good video if you wanted to pick it up! Just spreading the word to stop good working machines going to scrap.
Nice clear video. The new disc & sensor hasn't cured mine. Could be a fault further along the wiring. Its intermittent fault. It affects the automatic hand brake as well.
thank you so much for this video for people who have a sound from the pump !!! i sprayed it full with wd40 and yes the sound WAS GONE .. thing was making like 6 months of crazy loud sounds finaly its gone
@@green-crocs-fixes1520 I can only make it better not worse, I guess. LOL I am concerned if the bands are broken on the correct position to install them.
That’s helped me out loads - mine blocked completely - nowhere on Gaggia are there any step by step instructions for sorting out the machine when the machine is stuck on purging mode due to limescale blockage - thanks for sharing 😊
You should've replaced the bearings on the fan blower motor. Just lubricating with oil won't work for long. They are easily replaceable, type 609z if I'm not mistaken. Anyway, good job!
Thanks for the video. I have the same issue with the intuition preference EA872B. It looks totally different inside 😹. Any chance you this could be the same cause ?
What a horrible design for an engine. I have a 207, getting the nuts of the sensor was bad enough , but I could not get the sensory out. It just refused it's almost like it's latched onto something else that was not visible. I could wiggle it very very slightly but only couple of millimetres.
Hi Kulwinder, yes there is. you can gain access via the Fan housing @ the bottom right, just have to remove the front cover top.housing, housing ring and then the Fan.
These seats get filthy as children often have snacks in their seat. There are so many reasons why cleaning is a must. They also cost a fortune to buy so refurbishing like this is more hygienic & will keep insects off & wasps entering the window. Food stuck on seats and buggies also attracts dogs & wild animals & even attract rats to chew their way into a car from beneath, which can be dangerous to children. Refurbishing also means it can be passed on to others, this is better for our environment.
@@green-crocs-fixes1520 Many of us are. Especially if it looks like a struggle we think 'oh perhaps not meant to remove' & I suspect manufacturers would rather we toss them & fork out for new ones. Seeing things clean is not only uplifting in some strange way, makes us feel purged, but it's also the hygiene side. We sterilise our babies bottles & soothers then let them rub them on grubby car seats they can spend long periods in. So the video is very important for parents. x
For my problem I’m am trying to play the Deadpool game for the 360 but every time I try and play it it says cannot read disk and to clean it however the game is basically brand new and has little to no scratches on it I have been able to get it to show the publisher of the game but then it crashes and says the same thing I have try it with other games that have a lot of scratches and the game works perfectly fine can you plz help 👏👏👏
Thank you Green Croc for uploading this very clear and no nonsense video, one which helped me with a similar problem. I’m now subscribed to your channel, many thanks.
Hi, nice video. I can see you added a flat belt, make sure its same with as the old one. Also, if the rubber is dehydrated use some cloth to remove the particles of rubber on it, you'll notice them. It will create more contact with the flywheel. Helps getting less wow&flutter during playback. I got the E12 on the bench now. Nice work.
I'm definitely giving this a try. I got a 360 out of a scrap pile that didn't work at all. First, I managed to get it to boot by cleaning up corrosion. Then it wouldn't put out an A/V signal, but I've determined that the HDMI port still functions. All that's left is to get that disc drive to work, which why I think they tossed it in the scrap pile to begin with.
Hi Kowosky, I assumed it would be a standard. Found this one on the internet www.ebay.co.uk/itm/296400668892?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=t6w3iotmr_a&sssrc=4429486&ssuid=PIDP2WFUT8e&var=&widget_ver=artemis&media=COPY not sure if yours looks the same.
There are no Bearings or Seal listed for an Eco or Sealed Tub Gerard, as they are not designed to be replaced. You have to measure the old ones once you have removed them then request the sizes from an online Bearings supplier.
I have 308 sw the fault pops up at least 2 times a year so this time it never reset itself so i did everything in the video only thing this time was engine was shaking bad - after doing it the light did go out and came baxk on but the car runs so smooth now
