Worked like a charm. Thanks. I have also ordered a new spring because the old old may not last too long.

Thank you!

Thanks for the video

Great fix!

I know this is an old video but I’m glad it was still available. Saved me money, thank you

Thank you! In my case the bottom of the spring broke, but this video was incredibly helpful!

You saved my moms life !! We thank you so much for your video. 🥰🥰

Worked perfect for me. Thank you

Wow thanks for video..... I was about ready to do something drastic to that microwave! The first time I worked on it was last week. Tore the front off and thought it was the middle switch...popped it out and it seemed to work again so put it together enough to try it and BAM it worked! I was patting myself on the back for the last week...until just a couple hours ago it did the same thing...blew breaker immediately on start up. I was thinking about maybe taking it out...like the ending its life take out. I wasn’t even looking for another fix on RU-vid...just figured it was the same problem....when your video shows up on my page....thank you Jesus....had to be a god thing!

Saved the day! Thanks!

What on earth were you smacking on

Which model of GE microwave is the one you just fixed? I am trying to get the spring for the door latch.

I don't have a spring open like yours and there are no screws

That was happening probably two years ago I did exactly what you're doing except with a knife and it would work but then it stopped and now it's completely as if the fuse is blown only the fuse is not blown in a door latch actually completely like bypass like a kill switch

Thank you!

is it a snap on ?

How did you remove the cover to expose the spring ??

People don't throw out you GE microwave before trying this simple fix!

All that talk of a separate circuit line to the microwave didn't matter at all! I tried that first.

My switches all tested fine also.

Marvelous! It Worked! Saved me over $200 for a replacement!

Akhil's fix is better than the zip ties. Best to drill a pilot hole for a #6x2" screw as there may not be much housing left to use a thicker #8. Don't over torque the screw as you risk splitting the plastic housing. Not sure how permanent any fix will be as the housing is so brittle. What a horrible design. Thanks for the inspiration!

Thanks for posting. This is the best fix I've seen for this problem

Worked great! Thank you! I tried zip ties and it worked for a day. The screw threw the plastic worked like a charm.

This worked like a charm! And fairly easy to do! Thank you so much for posting!!

Wonderful! Screw did the trick. Took the shade apart as per your video on the first one. For the 2nd one, just spread the 2 sides of the shade near the shaft enough to drive in the screw just behind the shaft. This was much faster.

I have watched this video two times, and I can't read that fast. Slow the video, please.

Worked great. Thank you for posting!

Thank you! Just fixed my driver side visor and took me 10 minutes. It had been hanging for months and gradually getting worse!

Thank you very much for saving us money on a replacement. Easy fix once you watch your video.

Thank-you! The screw worked great!

Thanks!!! This fix worked great.

Thank you! Excellent job. I plan on doing this to my 2013 Pathfinder this weekend.

Excellent, thank you so much Akhil for your instructions, this worked perfectly and saved probably $200 (and only took me 1-1/2 hrs) Very happy

thanks for the great guide. just fixed ours and only took about 10 minutes thanks to this. While I didn't see it mentioned, I would recommend drilling a pilot hole in the plastic first before going in with the screw.

worked..Thanks

How do you remove the clip? I can't seem to figure mine out on my Nissan Altima 2014? Thank you

I took my 2012 Pathfinder visor apart and the plastic inside had crumbled. Shouldn't this be a recall...?

Thanks for the inexpensive and effective fix!

Worked great! My demolished driver's side is better than new and my soon to fail passenger's side is reinforced.

what size screw did you use? i know it's 2 inches long. How thick? thanks

i have the same problem. I will not buy nissan again because of lot of problems like these

Wow, big thanks! Save me a lot of time in trying to figure it out on my own.

Thank you for this! Just did this and now my visor loves me again!

Thanks much! Just fixed the left visor on my 2013 Pathfinder. Cost of a 2" deck screw and 30 minutes of time! Great video!!!

Thank you for sharing this video, I am going to fix both of my visors, saved me about $200.00 bucks!

This was AWESOME!....Yes...The dealer sells the entire visor for $125-$140. In my situation, the entire Plastic section broke. Placing the screw through the Metal Clamp was ingenious! Thank you for sharing...saved me money and peace of mind that if I have to suddenly stop, I won't hit my forehead against the Visor....Nissan should learn from this engineering trick! Much appreciate. (Added Note: When separating the visor, be careful prying the half apart...the snap ons have plastic clips, so be careful not to pull apart to hard...they can break.) THANK YOU AKHIL! great Video!

Excellent video, has save me at least $100, I've repaired the passenger side. I'm sure the driver's side will go next. not very difficult at all. probably took me 15 minutes

Excellent video, has save me at least $100, I've repaired the passenger side. I'm sure the driver's side will go next. not very difficult at all. probably took me 15 minutes

Excellent video, has save me at least $100, I've repaired the passenger side. I'm sure the driver's side will go next. not very difficult at all. probably took me 15 minutes