Black mastic glue has asbestos in it. Should not have done this

Very good job greetings from UAE

What kind of silicone did you use? Anything special?

I tried to purchase the Makita CA500x it is no longer available. Do you have a replacement recomendation?

thanks for being so informative in what your doing, great video!

Very nice thank you!!

Came across this looking for ideas for around a wall vent. I'm replacing baseboard with taller one. Absolutely perfect! Love this! I finally found someone who thinks like I do! Lol

I would use double-sided glazing tape... instead of silicon ..

what type of screws did you used for the framing and for the panel?

No sealant under the miter no concrete screws and washer back coping 👇no pop rivets

Jaim trop trop ca mes jai pas eu la chance d aprendre ca

Thank you!!!

Thank you for a great video and explanation. I've always wondered the best way to install composite panels and you have nailed it with your video.

So, did it helped because you got the door frame pulled tighter against the edge leaving room for the door? I have this problem and I think your method will take care of it.

Love this video!

Professionally done👏🔥

I know even what to say, but Thank you!!

I work excellently on that material here in Colombia, I even make it in 3D if they need workers I'll go there

This panel system is alot different from I I stall here. With ours we get them made in shop and they have a bunch of supports everywhere and then the clip system is built in where you just have to slide the clips into little channels instead of screwing right to the panel otself

Any idea what the thickness is?

Fix that audio brother can not understand most of the important stuff at the end of your video.

What product are you using? That is a very nice job you did.

DO NOT DO THAT! Saw or grinder cut with friction that will burn off galvanized coating… without it all the cuts will rust in no time.

Nice job

Wow. No bondbeam or any reinforcement at all it looks like. Fail.

Great video. Thanks.man

Soy mexicano este trabajo esmimero mole

Great job nice and informative you solve my problem thanks

That adjustable slide is clever - good work

Nice work. I’d love to see you caulking a half inch gap.

This same thing absolutely happened to us in the uk, white panels were fine but darker panels got to over 50c and just buckled all of the sealant we had when we returned the next day ! Lessons learned

Thank you so much for the great video Mr. That final cap on the seams looks much better than under.

Gracias por compartir este video voy a comenzar un trabajo con los mismos materiales seguiré tus consejos Dios te bendiga a ti y tu familia y tu grupo de trabajo

What’s the name of the sealant and where can I buy it? Also, what kind of silicone did you use around the metal trim you used? Thank you.

what a pain in the butt

there so thin I would just leave alone an put new flooring over it life is to short for that Job 😁 MAYBE 🤔🤔🤔

25 years in commerical sealants and i have to say thats a Great bead but i have a few suggestions. Your backer should be roughly half as deep as the width of the joint. Spray foam is problematic if you dont let it fully cure. The soap solution if a good finishing step but should never be used as the only tooling method. Wetting the joint before dry tooling can prohibit adhesion even though it looks sealed. Pro tip- you only need a small amount of soap in water and a spray bottle makes it way more user-friendly.

nice video, have your phone horizontal not vertical

Thank you,massive respect for your work

SUPERB !! great video with very clear instructions. thank you. you are a very good teacher

Have a question for you, how real caulkers do it here in Phoenix Az. during the summer months when temperatures are above 115° or more during the day...?

Do you do work in Ontario, Canada?

Muy Profesional

Midwest snips are by far superior than any other brand

I also have an aluminum coating on my roofing membrane? Do you know if the rubber roofing can go over the modified membrane that’s there?

Hello What thickness of the of the panels do you use im looking to do My commercial garage and im not sure what to get can you help me out will any of these about work best 1220*2440mm, PVDF coating, plain color, normal polyethylene core, 4mm / 0.50+0.50mm, 4mm / 0.40+0.40mm, 4mm / 0.30+0.30mm, 4mm / 0.25+0.25mm, 4mm / 0.21+0.21mm, 4mm / 0.18+0.18mm,

Very helpful. Thank you!

The equipments which platform can I get it to buy

Please how do get to learn more of this work, is really in my interest

what type of router bit you are using to grove and cut aluminium composite panel? can u send me model? or just use wood router bit and its work?