Welcome to "PapaBonusFPV"!!🚁✈️ Join us for an exhilarating journey into the world of FPV drones. Experience the thrill of flight, jaw-dropping maneuvers, and stunning aerial footage. Build your own custom drones with our guidance. Let's learn, share, and inspire each other. #FPV #DroneFlying #AerialAdventures #DIYDrones #FPVCommunity Subscribe and let's soar together!
Mines started to play up badly as of today. Sound keeps cutting in and out. Had 4 bottom input lights on at one point. Tried resetting and powering off and stuff to no avail. Loud popping at times too. Quite sad as it's been a great speaker system used almost everyday for just shy of 11 years. I habe no idea how to replace parts so just looks like ill have to buy the set again. its increased in orice a third since i got it in 2013
@PapaBonas not quite, although it helps others to provide that info. It seems like you are only using Labs to enable stock camera features, without any Labs extensions. Most FPV Labs users are at a minimum over cranking the bitrate, but there is so much more. Experiment.
Mine just stopped to send signal on rear right Opened and everything seems fine around output Measure everything i can and everything has a value. I don’t have any knowledge about how to fix it and i was hoping to find a fail resistor or capacitor to replace Anyone have any ideea what would be the problem?
Honestly very little: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7GweG0RnCfc.html I followed this guys instruction and it did help me out tons with the staying in the air problem
HOW TO FIX IF SUBWOOFER IS OK BUT CONTROL UNIT NOT WORKING : Attempt 1) Turned on unit, got zero lights. Tried the Logitech Factory Reset (Turn off control unit, then hold the input button for 8 seconds) and saw 2 input lights turn on, but no sound. Tried this procedure several times, and got 3 inputs lights, then tried again, now with 4 input lights on, but again no sound or other lights. Attempt 2) Disconnected power to subwoofer for 30 seconds, and tried Factory Reset again, with same results as Attempt 1, but now with 3 input lights on. Attempt 3) Disconnected cable from Control Unit to subwoofer, waited 30 seconds, tried Factory Reset yet again, with same results as Attempt 1. Attempt 4) Disconnected power to Subwoofer and Control Unit cable. Waited 60 seconds and tried Factory Reset again, and got same results as Attempt 2 - No Joy. Attempt 5) Found this video, and although was not that helpful, tried Attempt 4 yet again several more times and on the last try, this time it works, and my Z906 is back to normal ! Lesson Learned : You may have to power the subwoofer down and disconnect the control cable and then try the Factory Reset Proceedure more than a few times to get your Z906 back into its working state !
Hi guys i found the solution, i repaired almost 5 z906 with out problems 😮, the solution is cheapper but you need to change one component un the main board, regards
3 lights = no serial comm between console and main board, 2 lights = no readiness signal from amp. I also had two lights. The cause was the black stuff they poured all over the PCB. It got conductive (sometimes lower than 200k). Once I removed it, the system came back to life! :) Be very careful though not to lift/destroy an SMD component. I ripped Q8 unfortunately - because of that DD5.1/DTS decode no longer work - only dolby surround. If anyone could tell me the part number of Q8 I'd greatly appreciate it (it's right of the "sub out" connector).
@@michaelneuweiler8161 maybe u have an answer to my problem aswell. My Problem is that the lights are jumping through the whole thing, cant press anything either.
Nice flight. I too am still just uploading the DVR footage. It's terrible but it's proof you got some flight time. This flight is a lot more stable than my first few videos.
Really appreciate it thx! I am looking for something like a Thumb cam from RunCam, a GoPro naked as well as the Insta360 GO 1 or 2, but for now the Action cam is all I have... :D
@@kitten-whisperer Actually the pro does allow it. It has 3 modes, normal for beginners, sports for going fast withouth height sensors and acro which is full maddness...
@@kitten-whisperer apologies for that yes you're right in sport mode you can't flip it it does speed up and increase the the rate at which you can turn and move but you are correct you cannot flip it and sports mode you have to go into manual mode which is the third setting.
Howzit, I am using a Skydroid UVC OTG for android. Eachine also has one and it works sort of ok. Its not perfect in that the skydroid fpv app for android crashes the whole time, so I started using Go FPV, but as soon as I start recording the app crashes so in the above video I am actually recording my phone screen. Nice thing however is I am connecting both my goggles & the skydroid to the vtx at the same time... Link to the Skydroid...: flyingrobot.co/products/skydroid-uvc-dual-antenna-control-receiver-otg-5-8g-150ch-full-channel-fpv-receiver-w-audio-for-android-smartphone-colour-black