▶️How To Clean & Reseal A Transmission (Honda B-series)🔧

Подписаться 115 тыс.

Просмотров 889 тыс.

50% 1

▶️How To Clean & Reseal A Transmission (Honda B-series)🔧.Here I show you the steps to clean and re-seal your B-series transmission case. This works with any Transmission.
🛒Shop This Video: www.nthefastlane.com/b-series...
😃How To Know For Sure You're On Your Way To Heaven😃
www.nthefastlane.com/how-can-...
🛴QUALITY AFFORDABLE E-SCOOTERS ATVs DIRT BIKES AND MORE🛵
mototecusa.com/?AffId=2
🔥 NTHEFASTLANE'S TOP RECOMMENDED SCAN TOOLS 🔥
shrsl.com/47gmf
🔥 NTHEFASTLANE'S TOP AUTOMOTIVE TOOLS 🔥
🔧www.nthefastlane.com/automoti...
📽️Nthefastlane Product Reviews:
www.nthefastlane.com/video-ph...
🛒Nthefastlane's Amazon Store🛒
amzn.to/3BT3Lz1
🚨 NTHEFASTLANE'S TOP PICKS 🚨
Find Any Leak: amzn.to/3kWWAkU
Auto Repair Manuals: shrsl.com/3wmrh
LED Headlight Bulbs: amzn.to/3I4Hpg9
Brake Pads & Rotors: shrsl.com/29x6w
Radar/Laser Detector: amzn.to/3oWa1kb
Car & Truck Remotes: shrsl.com/29x75
Subwoofer Audio: amzn.to/3I8BIha
Car Stereo System: amzn.to/3s0t8LR
Car Audio Amplifier: amzn.to/3gYlZVV
Video Editor I Use: amzn.to/36vHlZ3
👕Nthefastlane Merch: / @nthefastlane
📧Join Nthefastlane's E-mailing List (No Spam): www.nthefastlane.com/nthefast...
Website: www.Nthefastlane.com
Forum: www.nthefastlane.com/forum
Troubleshooting Guide: www.nthefastlane.com/automoti...
Honda Database: www.nthefastlane.com/honda-da...
Facebook: / nthefastlane
Instagram: / nthefastlane
Tiktok: / nthefastlane
Twitter: / nthefastlaneceo
(Honda Torque Specs App For Android)
LINK: tinyurl.com/y77f78or
*As an Amazon Associate Nthefastlane earns from qualifying purchases.
*Nthefastlane makes Commission on most links in the description and comments.
Due to factors beyond the control of NTHEFASTLANE, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Nthefastlane assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. NTHEFASTLANE recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of NTHEFASTLANE , no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not NTHEFASTLANE..
#BestMetalCleaner #TransmissionClean #CleanAluminum

Авто/Мото

Опубликовано:

2 апр 2013

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 241

@Nthefastlane 5 лет назад

🛒 Shop This Video: www.nthefastlane.com/b-series-transmission-reseal-store 🛒 Visit Nthefastlane's Amazon Store: amzn.to/3pP4UCy

@declanosbourne62 4 года назад

Why you didn't use gas to clean the transmission man.? U cant beat gas when you use it to clean grease.

@Strike86 8 лет назад

Man that was so satisfying... looked brand new when you were finished.

@Nthefastlane 11 лет назад

Thanks for the run down on the Permatex color code, appreciate it.

@tischlerbmw21 8 лет назад

I use purple power, with a scrubbing brush, and pressure wash it off. Works great, takes a couple of sessions of blasting off the oil.

@bigbluezuk 9 лет назад

I am very impressed with the oven cleaner; great find! It's actually a strong BASE and not acid. Those oven cleaners are solutions of sodium hydroxide and are actually pretty safe. Much safer in the long run than all of the degreasers!

@slosol1067 10 лет назад

Your tips on installing the housing back on help me out alot . Good job sir

@kimberlymunoz2817 11 лет назад

I just saw all your videos,They're videos are so inspiring to me . Keep up the good work. I'll be looking forward to see more of your videos :)

@avineshsurujbally9170 5 лет назад

Easy off is a bossss !! An after jus one try it’s perfect then I sanded an hit my trans with a clear coat .

@Ronco160 7 лет назад

I cleaned my ls trans today. I tried Walmart degreaser and a pressure washer. brake cleaner worked the best.

@45Mang 10 лет назад

Pretty simple vid. Thanks a lot bro!

@cbarr0288 10 лет назад

Very nice, this should definitely help my cleanup on my DSM. Thanks a bunch. Never would've thought of oven cleaner. I have tried carb cleaner, "LA's totally awesome" and Purple Power (In the purple can, not orange). Nothing seems to work well so far. Especially getting into all the tight nooks & crannies. I have the same engine de-greaser in the cabinet but I just skipped it. I may have to re-seal the case the same way, there was a slight leak before.

@mrcinpro8403 10 лет назад

mineral spirits with a round cleaning brush for the auto store works like brake cleaner only it doesn't evaporate nearly as fast. it worked well on the top layer of gunk inside the bell housing, and 90+% on the outside grime is gone. oven cleaner does work really well. if you don't like the look of the aluminum afterward hit ti with some high heat cast aluminum paint.

@monmorgandy 7 лет назад

"Just be careful." *magnet goes flying across the room* hahaha. Good thing your floors were pretty clean!

@AlexanderLopez-kn5bt 5 лет назад

I really like that job very clean 👍🏻

@williamcarter3642 6 лет назад

Mineral spirits for cleaning? Cleaned a 4l60E with it. Worked pretty well too.

@bobbyfields1824 7 лет назад

brake cleaner is the best stuff to us on something like what you have there thanks buddy for takeing the time to make this for us

@watchmanonthewallcouk6498 7 лет назад

Great Job !! Thank you

@Nthefastlane 11 лет назад

Thanks, Not right now but possibly in the future.. I have a quite a bit of Honda How To videos coming up soon.

@brycedewaal7955 5 лет назад

Poor input shaft..

@slightlyslammed 4 года назад

came out super clean with the great value oven cleaner! FYI, those 2 retention bolts are not going to be found on a 89-91 B-Series cable transmission. that’s what i am working on. DA

@javiermartinez5000 4 года назад

Fuxkin GOAT simple yet informational!.

@alomec559 11 лет назад

Very good. Good instructor

@OutOfOrderMai 9 лет назад

Great video!

@blix8787 7 лет назад

thanks for the video. by any chance do you know of any channel that shows you how to do a harness to install a b16 into a ek...

@marcelb5296 6 лет назад

Nice clean job...👍

@ej8_felipe651 7 лет назад

Very helpful vide thanks

@JaydenIsTheName 8 лет назад

you need to use the OG purple degreaser and a soft bristle brush. gets really clean

@weldorguy 4 года назад

Hey brotherr!!!! I got your app and it's awesome!!!!! I'm subscribing:)

@asifaslam1111 6 лет назад

Nice work man.

@CarlitosBXNY 6 лет назад

Do you have any videos on a full swap from Automatic transmission to manual on a D16Y8 VTEC engine?

@michaelmotorsOFICIAL 4 года назад

Good video👌😁

@kiran-wh9wg 6 лет назад

Just spray diesel and clean it with a big paint brush. Repeat the process 3 to 4 times and the the results are amazing and cheap

@byAnArgentinian 5 лет назад

or just gasoline! I think gasoline is stronger

@JM-yx1lm 5 лет назад

@@byAnArgentinian no dude, gasoline evaporates in seconds. Think first before you say stuff like that.

@JM-yx1lm 5 лет назад

@Johnny Five kerosene is almost identical to diesel

@byAnArgentinian 5 лет назад

@@JM-yx1lm so what'd be the problem? It's the strongest and cheaper cleaner I've used. It's no good for rubber, plastic.. but for bare metal, why not?

@lickymywicky6289 8 лет назад

Diesel fuel well cut thru grease, like a hot butter knife thru butter.

@drwombat 7 лет назад

lickymywicky it did a decent to mediocre job when I cleaned my diff and left an oily residue it was the first time I ever tried to use it but will try using it again

@2kbaby924 6 лет назад

Nick Armock rust? Most transmissions are aluminum

@byAnArgentinian 5 лет назад

@@drwombat use gasoline, doesn't leave oil residues but it's stronger, careful with rubbers/plastics

@teeforrest3733 7 лет назад

Excellent

@2kbaby924 6 лет назад

How about a pressure washer?

@CrxBreizh 8 месяцев назад

Fantastic.

@lawrencemazzoccojr.6197 7 лет назад

I used regular purple power, scrub brush, 2600psi pressure washer and plastic jug caps fit the in the oil seals to seal out water. rinse, dry it off, then wd40 for corrosion protection.

@julloa1113 8 лет назад

the process is the same for a D series so would the torque be the same as well?

@rustybritches6747 8 лет назад

how long before you can fill and drive the transmission after new seal?

@etrinidad73 5 лет назад

Is it the same process for an automatic b18b1?

@crmercer6407 7 лет назад

do you need to replace the drive shaft oil seals after spraying the oven cleaner?

@codywichman213 7 лет назад

merce. all that work to reseal the trans, but skipped the verry ruined axle seal, damaged input shaft, and the worst rtv you can buy. all that work and the case seal wasn't leaking

@TPSYKRT 8 лет назад

I have a question if you can answer if you could please! I have a 1995 obd1 b18b1, I currently have a d15b7 block with a y8 head (mini me) and I was wondering if I could use an obd1 harness from a d15b7 5 speed on my obd1 b18b1? In my head it should fit because they're both obd1 and non vtec so can I do this or will I have to do some wiring for the dizzy, alternator etc.? It's going in an ek coupe and I'm using a p75

@matthewarnott1080 7 лет назад

is the clip the same on f and h series trans?

@enriquepena3538 8 лет назад

what about 1995 accord lx automatic what type is it

@Ibnhome 7 лет назад

should lay something on the ground in case it stains keep up the good work!

@potardo9851 4 года назад

Old shower curtains work better than a tarp at that.

@armchairtin-kicker503 Год назад

Super Clean is a very good degreaser, a product worth trying.

@fishslayer626 10 лет назад

How do change the seals where the shift linkage goes??? Please help

@NowOrForeverNever 10 лет назад

Nice video do you have a transmission rebuild video

@christophermariani3471 7 лет назад

@Nthefastlane i did the reseal now i have no neutral am i missing something i only have like 3 gears & no neutral us there a step thats missing its driving me crazy please lmk asap ?

@richardharber8434 8 лет назад

can u do an episode on d16 shift shaft replace

@mrgreenswelding2853 8 лет назад

oven/grill clean is not acidic, it is an alkali. sodium hydroxide.

@andymeng623 7 лет назад

Cool vid bro, I know this will sound unsafe and probably not advisable but I use just diesel or petroleum. It will break down and cut grease like nothing. I literally just pour a little and scrub with 3m scotch and a tooth brush. lol

@husseinhamdy2394 6 лет назад

grandhustlenz هسيي.

@Ali-uv3dz 10 лет назад

good video

@hussamadigasataneh1409 6 лет назад

Good jop pro.....

@un-_-known688 5 лет назад

Inbetween them two studs the nut what's it for ?

@PerformanceDubs 8 лет назад

Zep morado works perfect but will eat aluminum if left on too long.

@chrisfitzgerald2524 2 года назад

So I have a s40 d series trans that I’m cleaning! It shouldn’t hurt it if I pressure wash it should it??

@zforbes839 2 года назад

i know this is an old video but i still have a bolt that i think goes next to the two 12 mm shift fork bolts. it’s a 19 mm and i wasn’t sure if it goes in before i put it in the car or after

@Migycrz 10 лет назад

Nice

@JR-kl3cp 3 года назад

Can I use break cleaner on a cloth ? Then wipe of the old seal areas ?

@2strokeFORever 10 лет назад

Instead of prying the bearing with a screwdriver I just make sure the snap ring is open, flip the trann then hit the input shaft with a rubber mallet

@jerrybangngayan1252 6 лет назад

How to change the leaking water jacket of ingine with dismantle

@metaphor239 6 лет назад

2014 Chevy Malibu LS 2.5Ltr 4 Cylinder. Literally the wall from the bottom front left of my transmission case is bleeding due to a small collision. The crack cannot be seen with the naked eye. If wiped clean it takes about a minute for the wall to bruise and start bleeding. The crack is like the thinnest finest cut ever. Recommendations?

@Nthefastlane 6 лет назад

+Jay Bojorquez I would sand the cracked area, then use brake cleaner to clean it. After that apply JB Weld and let it sit for the recomended time. Atleast 24hrs and you will be fine.

@metaphor239 6 лет назад

Nthefastlane How deep or how much with the sand paper??

@homerobarbosa1172 6 лет назад

Do you know Karcher or Wap? It's a real soluction. But you did a great job!!

@Deathoar 5 лет назад

Pressure washer and a wire brush bud. Itll work miracles. Then to get the shine, chrome polish, a drill, and a metal drill brush.

@toddclark23 6 лет назад

I have found that LA's totally awesome cleaner works best, don't really even have to scrub it, $3.00 at Dollar general set your part outside so the sun can warm up the grease, spray come back and pressure wash it, doesn't change the aluminum finish either.

@theedge5584 3 года назад

I've seen people change those springs in the bottom what are they for

@loxiong6071 9 лет назад

what is the name of the song in your intro? Sounds GOOD =)

@kiran-wh9wg 7 лет назад

diesel + paint brush is the best for degreaser etc etc

@MrVidrio187 10 лет назад

Holy intercooler!

@jose.ramoscaban 8 лет назад

Help please! will be the same process for a D series transmission?

@Nthefastlane 8 лет назад

Yes, same exact process.

@jose.ramoscaban 8 лет назад

Ok thanks

@mushy18100 6 лет назад

Way much lighter work than B series

@JM-yx1lm 6 лет назад

Depends on what year it is...

@suspendedhatch 8 лет назад

I have some constructive criticism- I appreciate people contributing to public knowledge but there's a lot of unhelpful stuff here. Big thing is don't put the main shaft down like that. Space it up off the ground with some boards or bunch of cardboard at least so you don't cause damage. Those cleaners don't really work as you found out so it's not helpful to suggest them. You got it clean by plain scrubbing it out which is what pretty much anyone will do by default. Easiest most effective way to get these clean is with a power washer. It will take thick layers of crud right off with minimal effort. It's a good investment for cleaning engines and parts and has many other household uses. It's also easier on the environment and your health as you don't use any cleaning products. You're not putting scratches into the trans with wire brushes etc. You did a good job of showing how to plug up the axle holes. You have a careful approach, pretty good pacing and explanation but I would re-do the video using a pressure washer.

@bauerleinjohn Год назад

@@TaylorKing1 it’s not lazy, it’s smart and if it works better and faster then why not

@345eg6er 11 лет назад

h7 or purple blaster mix half with water pump bottle few times, spray it that it comes out like foam leave it on about 20 mins and power wash it off and spray it down after with wd40(if u want) and bling!

@builtandraised 4 года назад

Can't figure out how to get the case on the part in the video at 15 minutes 25 seconds been at this part for a while everything else seems to be okay, any tips?

@andrewruibal9480 7 лет назад

you dont need open the trans to figure out what trans you have but great video sir

@user-js8fm1nk8s 6 лет назад

Я бензином и щеточкой промыл. Всё отлично

@maveric0738 7 лет назад

Personally Parts Cleaner is the best. If you have access to one.

@JM-yx1lm 5 лет назад

Your comment is dumb. What if the parts cleaner is full of citrus cleaner? Ya,,,see what i mean. You would have sounded much more smarter if you actually named a solvent to use IN tge parts washer.

@Nthefastlane 11 лет назад

Lol, I thought about that...kinda wondered why I inspired a girl with automotive :P

@arthurl.1263 10 лет назад

I have a d16z6 manual trans without grinds but the input shaft has play. Any tips?

@2xMUCHxBASS 10 лет назад

Probably needs a new main shaft bearing(input shaft bearing). There are tutorials on forums but open trans like he does, pull main shaft and its the bearing in the case, on a b series anyway.

@PeterFeederHQ 6 лет назад

Logically speaking. No matter how hard you try to keep any kind of sealant material from going into your engine or transmission, it will still make its way inside! When you bolt any 2 pieces and sandwich them together, the sealant material gets squeezed in and out of both sides. I don’t know where the hell these DIYs or certified mechanics get the idea that if any gasket material gets into your engine or transmission, it’s gonna 😱“blow up!”😱 Any soft debris inside gets burned up or ground to hell into tiny dust. Unless it’s a piece of metal, then that’s a different story. That’s why the Engine Oil Filter and the Transmission Filter Exists, to filter out any debris. *Your engine will not explode because of pieces of RTV*

@byAnArgentinian 5 лет назад

it's never a good idea to have any kind of contaminant on the lubricant. No matter if it's soft.

@caleb5702 3 года назад

Could aluminum brightener be used?

@leeanlrivera8482 6 лет назад

good video you opened the transmission but did not change the seal of the input shaft

@savages8077 9 лет назад

Use a 8mm Allen wrench works wonders

@gundersonbrandon 10 лет назад

very nice tutorial good job and thanks

@Nthefastlane 10 лет назад

Brandon Gunderson Thanks Man!

@Taylor57179 3 года назад

LA.s totally awesome cleaner at dollar tree works perfect for that kinda cleaning

@x-man4702 7 лет назад

Use Hondabond next time you reseal a transmission, it's great stuff.

@eksine 5 лет назад

Overpriced, permatex black rtv is $7

@Evergreen_Kings 5 лет назад

Used Honda bond on my b series swap 15 years ago, no leaks to this day. Don't cut corners :) it matters in the long run

@markhingst5368 3 года назад

@@eksine black rtv works fine but don't fool yourself that they are the same thing. Put a bead of each side by side and you will see they are quite different.

@eksine 3 года назад

@@markhingst5368 as far as I can tell when I did both engine oil pans for the Accord and odyssey and oil pumps, the old Hondabond came off cleanly like it had no stick. And scraping off new permatex was harder like it was glued on because I needed to recheck something, so yeah they aren't the same, hondabond seems inferior so I have no clue what you are harping about

@markhingst5368 3 года назад

@@eksine harping? Lol, I made 1 comment snowflake 🤣

@stevedubman8039 7 лет назад

You don't have to be so careful with sitting it on the input shaft. I agree about the power washer. If my input shaft took damage just from the weight of a super light trans-axle I'd never drive that car again. Nothing made out of porcelain here :P

@stevedubman8039 7 лет назад

Commented without finishing. Yah dragging the whole thing around hammering it trying to crack the case was brutal.

@pjwarez 5 лет назад

Oven cleaner is Sodium Hydroxide, which is a Base, not an acid.

@adanCOIN 5 лет назад

Sweet deal brah!

@averyalexander2303 7 лет назад

Gasoline will cut through that grease very quickly and not leave oily residue.

@jorgelozano9102 6 лет назад

Dry fast tho

@JM-yx1lm 5 лет назад

It evaporates in seconds. Gonna cost 20 bucks is gas to do this. Use mineral spirits.

@sentree9857 5 лет назад

@nthefastlane I have a 97 honda del sol Vtec with 86k miles. It has the b16a2 engine. Some times when I'm at a stop/red light i have trouble getting it into 1st. None of the other gears are a problem except for 1st & reverse, but mainly it's 1st that's the issue - could be because I just notice 1st more since I use it more often than reverse. The clutch grabs high and seems fine and has fluid in the reservoir, however it is a tad bit dirty but nothing crazy I guess. I just recently changed the transmission fluid with honda mtf about 1k miles ago but still notice this problem. Any ideas what this could be? Its kind of been a pain in the butt because some times I'll get honked at if I'm not moving right away when the light turns green trying to get it into first. I also notice that 1st and 2nd don't seem to glide into gear as easily as 3rd, 4th, and 5th. 2nd,3rd,4th, and 5th always go into gear but it just seems that 1st and 2nd some times seem like they need a bit more effort and don't pop into gear as smoothly. This is not my main issue but I figured I'd give as much info as possible. The trans makes no strange noises and aside from 1st occasionally not going into gear it works fine. Any ideas on what could be the issue?

@APEX70210 5 лет назад

Sentree slave cylinder or bleed you clutch

@seando87 3 года назад

I tried that brand engine decreaser before. It sucks. Me, my brothers, and my dad have always used some sort of oven cleaner or diesel. Usually used diesel on tractor engines to clean them lol

@jumu6159 9 лет назад

i think paint brush and diesel would do the work pretty much better

@un-_-known688 5 лет назад

The nut is there a 3:59 in between and above them two Bush mounting studs that's the reverse idler shaft bolt... am I correct

@Nthefastlane 5 лет назад

I'm pretty sure you're talkin about the reverse idler bolt. It should be longer than your index finger.The required torque for it is 33 foot pounds. If you want to fill your transmission fluid without doing it from these side, you can always pull out the speed sensor. It requires a 10 mm socket with a 12in 3/8 extension. unplug the clip and pull it out.

@Nthefastlane 5 лет назад

You can watch my other transmission identification video here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Smy2TYEPmDE.html

@paulbryan1969 11 лет назад

Why you using the sealant for, have fun trying to getting the bell housing apart, even more fun trying to remove it lol

@jasonalexander6417 5 лет назад

Nice video, but I find it easier to clean while on the car.

@lightspeedproject 7 лет назад

at 9:12, theres a little black sensor thing with 2 short green wires coming out of it, what is that?

@adriandiaz4940 7 лет назад

reverse sensor for backup lights

@goldomoreno 5 лет назад

So what happens if you forget to take the bag from the inside out and put the transmission together with the block?

@goldomoreno 5 лет назад

Lol will somebody please help me I forgot to take the bag out before putting the transmission on to the block do I have to take it all apart again?

@Nthefastlane 5 лет назад

If the bag is in there between the throwout bearing and the pressure plate it's going to start melting and smoking if you drive it. I wouldn't want any plastic residue on my clutch. If the bag isn't between the throwout bearing in the pressure plate you might be able to take off the transmission dust shield underneath and sneak the bag out. There's not much clearance between the flywheel teeth and the transmission housing. Another solution might be to pull the "dust boot" off the clutch fork and put some long needle nose pliers in there to pull the bag out.

@sideshot6951 4 года назад

did you have any problems with the transmission after?

@Nthefastlane 4 года назад

No. I have it in my 500hp build right now. Only thing changed was I used Permatex gray high torque RTV instead of the red/orange Permatex for the case sealing.