👉👉👉👉👉******IMPORTANT****** Please follow this video to better install the F405 Stack : ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bOLUu48OACU.html
Thank you very much for your appreciating 😊. I try to cover a build from the start to the finish, this mean it will fly, and if i miss something people are reaching out and i help them as much as i can after. This means to be part of the community 💪
Back again, apparently two months later. I bought the Bee35 Pro frame and built it this weekend. Your build video was helpful. I'm loving loving the quad so far!
I'm currently building one of these, i love Speedybee products. I have three Master 5 quads that i built and i'm so happy they came out with this frame. Thank you for sharing your build.
Building my first drone and chose the analog version. Being able to slowly watch though such a detailed step-by-step while completing this build is super helpful. And I’ll definitely remember to connect the esc to the fc before putting it all together.
Great job on this video. I had just ordered the SpeedyBee 35 Pro Frame and came across this during a search. One of the best assembly videos I have found for it. Lots of good information here. Impressed with my SpeedyBee products so far.
What an impressive video/tutorial. So glad I watched it. Bought this same quad off ebay and it was so jacked up. Got it going like a champ now thanks to you!!!
Great my friend! Happy to hear that 💪. Did you watch the follow up video? If you are using the speedybee mini stack i recommend to watch it to better install the stack 👍
Thank you my friend, please watch the video in the pinned comment before you build it if you have the mini stack from SpeedyBee, good luck with the build and happy flying 😉
Its a good stuff to change your esc firmware to bluejay, them you can use bidirectional dshot and use like rpm filter on pid, some tests showed its more efficient even, like improving you fly time
@@javmag9839 Thank you very much my friedn, I appreciate your dedication and your help.. it means a lot to me :) I have a lot of great content coming this year, so happy watching and thanks again for your support!
Great tutorial!! I used it as a "fixing guide" for a damaged Bee35 which I could repair and get back in the air again :) btw, where did you get the mask for the goggles?
Hi, thank you very much for your kind words, happy that i could help you 😊, what mask? If you mean the foam, i made a video about it and if you have goggles 2 it is a must, you will feel way better 💪: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-jgiDEj50yMc.htmlsi=8olmQ00vq2_mCygO
@@bilumedia I'm still at the beginning of the journey. I build speedybee master 5 v2 and Chimera 7 myself. Both drones have a stack from Speedybee. Now I'm watching your video and I'm thinking about building a B35. You're doing a good job and I'm watching your videos!!!
@@andreyspb1701 thank you very much for your kind words, if you need any help don’t hesitate to contact me on instagram ! I have more build videos ongoing now and well release soon 💪
Nice build and setup video! It's outside of the scope, but I've become a believer in pre-arm. I use my Trim-Yaw-Right as a pre-arm which work great for me as I have no use for them as trims flying quads.
thank you very much 😊! It is an amazing drone, I love it , it flies very very smooth and has ton fo power! I have no idea what is pre-arm! It is like a step that you have to do before arming?
@@bilumediaYeah, Pre-Arm (a mode in Betaflight) is an additional button (it should be momentary, IMO) that has to be pressed for Arm to happen. This prevents one from _accidentally_ flipping the Arm switch and have the props start spinning. Example: carrying both your plugged in quad and your controller... and the Arm switch getting accidentally bumped to on. In my config, I have to hold Trim-Yaw-Right before flipping on Arm (or Turtle Mode). In EdgeTX, the trim switches can be made to be pretty decent momentary switches. Maybe I'll make a video.
I know it is not a full replacement for prearm, but I have trained myself to always raise the throttle after disarming, which at least is a bit safer. I should probably look into setting up a real prearm on my larger quads.
Hello i am bilded SeepyBee35 by your video :) All flight but i cant see OSD, as i see you solder only 4 wires O3 without SBUS and G(Time 23:34). But in instruction to mini stack it's 5 wires =9v+G+T1+R1+G-SBUS. SBUS and last G didnt need?
Hi my friend, SBUS is for DJI RC2, I am using ELRS protocol and for this you don't need those, actually some times it can cause problems if you leave them! and for the OSD, actually yestreday I helped a friend with exactly this problem, let's talk on instagram : bilu.media 😊
Thanks for the help building this quad. I converted my Cinelog 35 into a Cloud 149 V2 frame ( absolutely bulletproof ), but decided to convert that again into this Bee 35 frame. It's quite an awkward thing to put together - and I lost count the number of times the frame standoffs fell out as you tip it upside down over and over again. One thing though - I used your PID settings as in this video and just moving the throttle 1mm sent the quad up really quick and angrily I disarmed and altered the settings to something more friendly. Just thought I'd point that out - did you notice that and change your settings before flying - I feel it would have just cleared off on it's own. Overall - It looks Great - testing time properly soon.
hello my friend, I changed the tuning after to the speedybee stock one, if you go to speedybee website, you will find a file on the drone page with all the settings needed and after I changed the rates to a cinematic really slow rates , because I am using it in commercial work more like indoors and near people, and I am flying it in Acro and it flies really good like this, I get like 8 minutes with the gopro 11 mini 😁
Thanks for this build video. Just received mine yesterday and I am starting to put together now. Since it is kind of an upside down build, it will be great to see how it is put together ahead as I go. One thing- I bought the pro version and am a little irritated that I missed in the fine print that the detachable gopro mount wasn't included with the pro. Also, no paper instructions came with mine.
You are very welcome 😊. Yeah unfortunately the little gopro gimbal is sold separately 😞, i said in the video at one moment that i think that it is sold separately, but i was not sure at that moment ! Sorry about that! If you need any help just let me know, good luck and have fun with the build 😊
@@bilumediaI'm loving this build. Installed inav at first with a lidar board hoping to get dependable locked in altitude when flying low and slow. I was not able to get altitude control to work well even though it flew very nicely otherwise, so I went to Betaflight. I may try inav again soon since inav 8 is out now.
@@kurtzFPV I didn't use INAV before, it sounds very intersting ! And the lidar idea is intersting too, I have something similar from and old drone... but I love to fly completly manual ...
@@bilumedia I too love to fly manually, even when flying indoors. But even the very best cinematic fliers show some up and down movement when doing a real estate fly through for instance. I was hoping to get the lidar mode working well enough just to use in such specialized instances. I was wrong in the post above. I tried inav 6 and it is inav 7 that has just been released. I thought it flew very smoothly in manual - just as smooth as Betaflight. But I actually prefer Betaflight return to home right now over inav, even though inav is far more precise. But it takes so much more tweaking, since it is also using a magnetometer. If it isn't calibrated exact right, the quad will start swinging in circles when using altitude hold or return to home. I'm sure I'll try inav 7 at some point. I'll let you know if I have more success than with 6.
Hi. Thank you fir your kind words 😊, with a 1300 mah 6s battery my flight time was 6:30-7:00 minutes, more like aggressive flying not cinematic and landing at 3,55 v!
Hi, sometimes you need and sometimes not, if you don’t use the dji controller 2 then i would cut them because you may encounter problems with the receiver not connecting!
Thanks my friend,i am not planing to use GPS with this drone, because it is more used for commercial projects and i don’t fly it far away! I have an M10 GPS and i think it is too big for this drone…
Hi, technically it will fit! So physically it fits but it will be a little tight! SpeedyBee Doesn't recommend to put this stack in the drone because it is a compact drone and they design the mini stack for it! but I guess you can install it and put the capacitor and receiver in different places where they can fit :)
@@bilumedia Oh gotcha, thanks for responding. I found out the hard way when trying to put the mini in my axisflying c25. “Technically” it does fit but I blew signal transformer when I squished the stack too much. Don’t want to make the same mistake :)
Hi, no it doesn’t fit a full stack and a caddx vista, i advice you to but the pro version, it is just slightly more expensive and you have the bottom plate acts like a heat sink for the caddx vista too and the caddx vista fits without any problems, there are holes especially for mounting the vista unit 😊
@@bilumedia thanks a lot for information ). Going to get the pro version then. It is not the higher price that I'm concerned with, I just don't like that it is sticking out that much from the frame. But ok, will get used to that
@@Curiousity0309 you are very welcome 😊. It doesn’t look bad at all and it is aluminum and it protects you air unit very good and there are some feet that the drone land on, so it will not land on the air unit 💪
Hello. What motors would you recommend for this frame? Currently I'm flying on my 5inch 4s 2450KV motors. I don't know what motors to select for this same build I'm planning to make. Thanks.
Hello my friend, i am using 6 s motors, you can see at the beginning, i present the exact motors, the are the axisflying c206 motors, you have link in the description with these motors, they are very very smooth and powerful im the same time,
Hello. I have a long range 7 inch drone build, i will drop it next week on Thursday i think! I explain exactly what parts i use and step by step build and a test flight at the end 😊
Would it be possible to state what length bolts you used that worked when mounting F4 Mini and DJI 03 installation and other screws in the description the Speed Bee Bee35 manual is very weak when it comes to what screws to use. Thanks.
Sure my friend 😊, i just opened the drone to measure them and the stack screw is M2x18mm with countersunk head, this one is provided with the drone, don’t use the one from the stack! And for the camera i used M2x7mm and for the air unit is the same M2x7mm as well, i mean secured with the TPU piece!
I swapped to M2x8mm to make mounting that tpu a bit easier. 7mm were just a bit hard to get started. Overall it is a nice build. A bit tight to button up and I'm not looking forward to taking it apart to add gps for inav, but it will give me a chance to neaten up the wiring a bit.
haha! I already saw that the cable to the ESC was missing when you screwed the quad together. I was wondering the whole time whether you left it in the video or whether you would quietly and secretly fix the error. ;-) I think it's really nice that you left it inside! I built the Speedybee 35 myself a few weeks ago and unfortunately only had 2203 3390kv stan fpv motors on hand but I think they are too weak on 4s. I have now ordered the speedybee motors and am excited to see whether they will finally fly better and more stably.
😂😂😂 yeah, i didn’t understand for few seconds what the hell is happening 😅! The 206 are very good, the drone flies really good and even with 1300mAh 6s batteries, i guess you ordered the 2006 6s?
Yes! I ordered the 2006 1950kv and I will go for 6s on them! I thought that Speedybee knows what is good for this quad… the xing motors are a little bit to expensive for me I think! But I am also very happy with the frame and the details Speedybee had thought of! I also put a COB led strip in yellow on it which looks great, but have you seen the new Speedybee meteor led strip they are offering now for the speedy 35? I ordered it together with the motors…. I hope it looks as good as in their promotions! ;-)
@@p_fpv You will be happy with the 2006 motors :D ! They sent me the Axis 2006 when I built the drone, I guess they didn't have their own motors yet, but I love how it flies!!! I don't have the COB light, it looks interesting, I will maybe get one 😁
I learned that turning off MSP on UART4 will disable the bluetooth functionality of the F405mini. I had to turn it back on, and then also turn on MSP for UART1 to get the dji unit working right.
Can I ask you a question? And why did you use the preset in the betaflight setup? Why didn't you use the dump cli from the official website for this drone?
Hi my friend, when i built this drone it wasn’t released yet, and i didn’t have the PID file, but it make sense of course 👍, but it flies very good with the preset too!
hey, nice video! i build the same drone with the same setup but have the Problem, that my drone disarms at half of throttle, did you heard something about such a problem? And what config did you wrote in the esc?
Hello my friend, thanks! I think i have bluejay installed! Do you have a failsafe active, maybe it is configured wrong and cause the drone to stop! Check the wires between the esc and fc, maybe change it, the motors run smooth? We can talk on instagram if you want and you can send me pictures and video maybe to try and figure it out : bilu.media
bro, your solder joints are not clean, when you are stripping the wires, you should only strip them to a short length. As a result, some of the wires are hard to solder and protruding inside the ESC barely touching the mosfets. Similarly use flux after tinning both the pads and wires for a better and fast solder connection. Otherwise, the build came out very nicely.
Hello my friend. Thank you very much for the advice! I appreciate a helpful comment like yours that helps me and others... I improved a lot my soldering skills from that build, it was due to bad solder and low temperature and of course the skills as well. I will take your advice into consideration 😊. thanks a lot
You fell the weight a little bit, but she can lift it without any problems, i love how this drone flies, i am getting strange camera movements now, it think the o3 lens is loose
Following along with the video and when you forgot the ESC/FC connector I was like "oh this will be funny when he catches it!" Great Video. Have you found any changes to the Tune you like after a few weeks of flying It or does it still perform well with that basic Whoop Tune you Picked?
🤣🤣🤣 yeah, i was waiting for the second part of the starting sound and it never came 😅😅😅! Thanks for your kind words and appreciation 😊. I am still using the tune that i picked here… but i didn’t fly that much lately to see if i would change something, the weather here in Germany is sh… 😅 and i am flying tiny whoops in my studio more, because i have some space to play around 😁
You are very cool. TY for this video. Can I build it with RUSHFPV RUSH TANK SOLO VTX 5.8G 48CH PitMode Pitmode 25mW 400mW 800mW 1.6W Adjustable 2-6S Microphone for FPV Long Range Drone and CADDX Ratel Pro 1500TVL 9.5g Super WDR 4.5V-27V NTSC/PAL CMOS FPV Starlight Night Vision Blacklight Camera for RC Drone? It's my first step in this... I have Radiomaster TX 12 (Edge Tx-ELRS), SoloGood Bandit Micro Elrs RF Module FCC 915MHz 1000mW/30dBm TX Receiver for Modeling Remote Controllers and ELRS 915MHz NANO ExpressLRS Receiver with T type Antenna Support Wifi upgrade for RC FPV Traversing Drones Parts. I hadn't have any expirience to fly on real fpv, only i Liftoff and Uncrashed.....
Why is that? It is not the best sound out there, i know, but it is not bas either! I mean it is clear and you can understand everything that i am saying! Thank for the suggestion though! I will consider this for sure 😊
@@Werbinich. what you mean overdrive? I was thinking actually to buy a rode videomic NTG since i dont have xlr camera and that one seems ok for what i need!
@@bilumedia Sorry i meant overamplified. i dont know a hole lot about mics either but the rode videomic NTG is a shotgun mic so its trying to record only in the way its facing. so if you are flying your drone and you are in front of the mic you are gonna be louder than the drone.
@@Werbinich. so you are reffering only for the video outside? because outside I used my iphone with the internat mic! inside I used a lav mic that is pretty good! maybe the editing is not perfect , I mean the sound edit, and the NTG is good inside for my youtube setup, maybe outside not yeah!
