TIP adjust plasterboard to stone ▶ ︎ • 🔥 TRUCO ▶︎ Cómo Ajusta...
✅If instead of doing the work yourself, you are going to choose to hire a company to do it, I have created a short guide to help you analyze the budget and avoid common deceptions in the sector. Head over to www.tutorialcre... to download it.
In this video we will mount a plasterboard ceiling under a stair ramp.
We will use omega masters of 15mm by 3m, screws, plastic plugs, wooden wedges and waterproof plate. Omega is usually used for when we want to lower the ceiling as little as possible. This system is perfect for when you want to go low. But if the surface is very crooked, it is not very comfortable because you have to use a lot of wedges and it takes more work.
🔺How to mount plasterboard wall- • 🔥 Cómo HACER una Pared...
🔺How to make a squad- • 🔥 Cómo Sacar una ESCUA...
🔺Place the door drawer- • 🔥Cómo INSTALAR Puerta...
🔴Links to materials / tools that I get online
- Screwdriver = amzn.to/3r1L2tH
-Red light self-leveling laser = amzn.to/2Lw66ty
-Green light self-leveling laser = amzn.to/3nphzIr
-Set of two scissors = amzn.to/38qVg0Z
- Bit holder with depth stop = amzn.to/2L9Xmt2
-fischer Sx / UX / (Briefcase of 290 Tacos) = amzn.to/3okzVvz
If you liked this video, don't forget to click I LIKE it and share it with your friends.
Video transcript:
Are you ready? Well take your tools.
We are going to use omegas, screws, plastic plugs and wooden wedges.
We check with an omega if the ramp is more or less straight.
In this case we have a small kink at the back.
The omegas distance must be 50cm between axes.
We mark on the side of the omega, to guide us when screwing it.
We place the first omega on the side, leaving a 4cm distance from the vertex so that when drilling it does not break the concrete.
We fix the omega in the center so that it is attached.
Now we fix the two sides of the omega on the upper side.
In this case, I do the same with the omega in the center, because the other side is a little crooked.
We cut a piece of omega and let it mount about 5cm.
We screw them on the side.
We fix the omega in the lower part.
We put a screw to hold a string in the lower part and in the upper part.
We tighten the string to be able to level the omega.
As we can see in this case, we need to lower the omega.
We loosen the screw to be able to insert a wedge and place a longer screw.
We make sure that there is approximately one or two millimeters above the string and we screw.
We leave a distance between screws of 50cm. We can also cross the screws.
Are you still there and still not subscribed? Think no more! Subscribe!
We do the same with the central omega.
Now we place the omega on the side.
We fix the upper part of the omega, leaving it level with the ones already in place.
Now we fix the lower part leaving it level with the ones already placed.
In this case we have to wear a lot. We will use a piece of omega.
We fix the piece of omega.
We screw, checking that it is level with the ones already in place.
We pass the string. In this case, we see that we have a few millimeters high.
What we do in this case is mash the omega a bit at that point.
We measure the plate and cut it a few cm longer.
Do you want a trick to adjust the plate to the stone? Check out this video.
With a beveled piece we mark the point where the plate will reach us.
We measure from the mark to the side of the plate.
We cut on the side so that we have the beveled cut.
Earthquake!!
We mark in the lower and upper part to draw a line.
We cut along the line.
In the slot we will glue the pieces of plate with pasta.
Soon you will have a video on the channel about the placement of the metal angle and the plaster. Make sure you are subscribed so you don't miss it.
1 окт 2024
