1.1.7 Packet Tracer - Basic Switch Configuration - Physical Mode 

Just FYI......It is as if it gets stuck at 96%. What I did to get to the 100% completion I saved all my work and closed the packet tracer. Then I reopened it as if I was going to make changes and it showed that I was at 100% instead of the 96% that it showed before. Hope this helps anyone else watching this later. Thank you Christian for the video and the ones you will continue to do.

You have the BEST tutorials, you have taught me more in the last 4 years than my paid instructors. Thank You

Christian, you're the man! I am studying for my CCNA at University. Please continue to make these videos. You have a new subscriber!

thanks Christian this is the only tutorial which is up to date with the current SRWE course

Mr Christian this is really a fantastic job: well explained, well understood, and well explicit, pls continue, switch configuration on a trunk.

Hello Christian! Thank you for all your hard work, I wanted to send you a comment before. I subscribed to your channel today. And I owe you thank you for all you do for the Internet community. Thanks again!

Thank you so much for this. You help me so much more than my online teacher.

Thanks Christian! I went to bed last night at 96% and when I woke up and loaded the PKI file it was at 100% and I hadn't changed anything. It had the same error you had at the end. Not sure why that happened but it worked.

Hey I can already tell; you videos are going to help me so much more than my teacher of Cisco II is... so thank you thank you!!

I can´t thank you enough... thank you professor Romero.

Thank you for sharing your knowledge Christian!

Thank you for the video! Keep them coming, please.

Christian thanks a lot men, you are helping me to get trougth my CCNNA certification

thanks so much, my professor isn't really useful for this kind of help, and meandering through the modules alone wasn't working for me either

Christian, you are a Genius my friend

Thanks man !! you are killing it Eveything is well explained .... keep it up G- 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥

Definintely earned a sub. Thank you for the help and the walkthrough.

Hi! before any question... jus say what an incredible help this is for me and many others that stumble upon your content. Very much appreciated all the efforts that you put out in this videos. Now my question: In this video, you checked the vlans and the vlan 99 was in the list with the command "show vlan", why you have to create it with the command "vlan 99"?

Gracias por todo amigo.

Muchas gracias por tus videos!

when i reached the terminal at part 3 it asks password after s1> enable the password should be cisco as I set it. but it is saying bad secrets. HELP

stuck at 96%, i checked the results and it shows the FastEthernet0 having an "X" mark on IP Address. how would i reconfigure this?

I have tried severally but my packet tracer won't accept ipv6. I keep getting invalid input

its great wonderful. thank you

thank you for the instruction.

at around 28:51 when I enter the ipv6 address 2001... it keeps saying "invalid input detected."

thanks so much 🙏🏾

You are THE BEST!

thanks for helping me

My progress is 88%, there are problems included in IPv6. how to solve it, thank you

I'm stuck on the stupid default gateway... Could you help? Like whats the timestamp if you know

Amigo, tuve un problema, exactamente en el momento que vuelvo a Terminal, pasa que me pide la contraseña, le doy la contraseña ¨cisco¨ se abre el modo normal entonces pongo ¨enable¨ y me pide contraseña yo le doy ¨cisco¨ de nuevo, pero ahora, por alguna razon, no me deja accesar ¿a que crees que se deba?

Tengo un problema con el S1> ..mi packet tracer se pone en automatico y no puedo salir o avanzar de ahi, me pide password...

thank you for this tutorial

In my terminal is blank.. so I can't configuration... Why that is happen??

Merci beaucoup

just starting the video, what messes me up is on the topology it says Fa0/6 but on the physical switch its all gigabit1/0/0 shit.

My Hero !!!!!!!

thanks for this video

Thanks. Nice video. I spent to much time to figure out what is wrong with the default gateway :(

what should i do for the last 4%

Hola, que buen contenido tienes sobre redes, te lo agradezco me has ayudado mucho, una pregunta, como puedo poner esa vista que tienes para ver los equipos en 3D ?

goat

Gracias por la ayuda amigo pero no puedo completar la actividad por un motivo y no localizo el fallo. En assestment items, en el apartado de IPv6 Address 1 la Prefix Length me aparece cómo incorrecta. Podrías pasarme el min del video en que lo haces o decirme cómo checarlo por mí mismo? Gracias

thank you

I get invalid default gateway message

Por qué no se puede llegar al 100%?

thanks man

Gracielas.

Im stuck at 96 it didn't reply to the Ping and also I went back to terminal and the pw ain't working..I swear I put in cisco