2011 Honda Odyssey Wheel Hub Assembly Replacement

Подписаться 501

Просмотров 17 тыс.

50% 1

FOR ENTERTAINMENT PURPOSES ONLY In this riveting episode, I show you how I diagnosed a problem with my passenger side front wheel hub assembly. I bought a Honda OE (original equipment) hub assembly and replaced the "replacement" that I had installed less than two years earlier. The video was made in January of 2021, and to date, I have had no problems out of the wheel hub.Please enjoy, and thanks for watching. It means a lot.

Опубликовано:

7 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 43

@jimmurphy5739 Год назад

Very glad to have hunted up your vid. There's another vid which grabs the search engine top spots which is all slick and everything, and it makes it look pretty easy. But that guy had a full shop, lift, garage and clean, fresh, fitted parts. There's no knuckle busting in that one, so I know it's not going to be like that for me. The idea of borrowing the slide hammer and puller bracket made watching this whole vid super-worthwhile. Thanks for the effort. Making vids isn't easy, but helps us out here in viewer land.

@DIYDanChannel 11 месяцев назад

Thanks so much for watching. There was a lot of adult language off camera on that one. The hub is still doing fine. I highly recommend Honda parts.

@rrmojo1 Год назад

thank you for the video. I know it takes extra effort to do this recording, but you help a lot of people sharing your knowledge

@DIYDanChannel Год назад

Thanks for saying that, Ronnie. That's why I make them. And you're right. It is a lot of work making videos.

@MrSamPhoenix Год назад

Great video man, I hope most Honda wheel hubs are as easily done.

@DIYDanChannel 11 месяцев назад

I hope so, too. Thanks for watching!

@scobecnickalex 2 года назад

Nice and I did notice that you forgot the dust shield. would be helpful to others if you edited video and put a note to put on dust shield before putting on the bearing. And add the torque specs for the hub. thx for doing

@DIYDanChannel Год назад

Thanks for the advice. I considered that, but sometimes I like to keep in the mistakes so folks can see how to fix the mistakes.

@jeffthomas9580 Год назад

Thank you for video, I saw that the dust shield wasn't on. I was saying camera person remind him that the dust shield is missing. Lol

@DIYDanChannel Год назад

Lol. I was upset when I noticed it. I appreciate you watching & your attention to detail!

@jameskim62 4 месяца назад

NICE WORK !!!!! SAVE SOME MONEY AND GET THE SATISFACTION !!!!!

@DIYDanChannel Месяц назад

Absolutely, especially in these times where everything is more expensive. A shop would have charged more than $500 just in labor to do that I'm sure. Thanks for watching!

@patm95 2 года назад

Awesome tutorial. Thank you!

@DIYDanChannel Год назад

You're welcome. Thanks for watching.

@jerrellstrawn6409 3 дня назад

My driver's side wheel was tight, but the bearing was howling.

@outofthinair1 2 года назад

How pissed were you when you realized you forgot to install the dust shield.

@DIYDanChannel Год назад

Super pissed. Taking it all apart again sucked.

@FD-rh6tr 2 года назад

Thanks for the tutorial!

@DIYDanChannel 2 года назад

You bet!

@javirodify Год назад

Very good video! I'm planning in doing this job soon. I have one question, how hard is to replace the inner tie rod on the driver's side? thank you for posting this video.

@javirodify Год назад

I just finished mine and it went very much like yours. Mine is a 2012 Odyssey and the specs for the axle nut is 242 Lbs-ft

@DIYDanChannel 10 месяцев назад

I'm glad you found the torque spec. Thanks for letting everyone know. The inner tie rod is not that difficult, but you need the special tool, which you should be able to "borrow" from your local auto parts store. It makes it a lot easier, and you will use less "colorful metaphors!"

@Nicedesk Год назад

Nice. Have an air chisel on standby if your car has been exposed to salted roads. Some anti seize couldn't hurt...for the next time!

@DIYDanChannel 10 месяцев назад

For sure. An air chisel is on my list of toys to buy.

@hurielramirez5406 Год назад

Very good job!!

@DIYDanChannel 10 месяцев назад

Thank you! Hope it helps.

@deesr.6641 4 месяца назад

how come he didnt have to press the bearing in

@DIYDanChannel 4 месяца назад

The bearing is part of the whole assembly. It's not separate.

@jerrellstrawn6409 3 дня назад

2010 and earlier required the bearing to be pressed in/out.

@samelias8440 2 года назад

Thanks for the vidio, it will be appreciated if you include parts number on the dicription, thanks

@DIYDanChannel Год назад

Sorry about that. Here you go. www.hondapartsonline.net/oem-parts/honda-bearing-assembly-front-hub-44300tk8a01?c=Zz1jaGFzc2lzJnM9ZnJvbnQtYnJha2UmbD0yJm49U2VhcmNoIFJlc3VsdHMmYT1ob25kYSZvPW9keXNzZXkmeT0yMDExJnQ9ZXgtbCZlPTMtNWwtdjYtZ2Fz Part number: 44300-TK8-A01

@jimstone1404 2 года назад

You don’t need a better screwdriver, you need the proper tool for the job!

@DIYDanChannel Год назад

I can't argue with that.

@daniellogges1998 2 года назад

What brand did you use the first time?

@DIYDanChannel Год назад

I forget the name, but I bought it at one of the major auto parts stores. Though it's more expensive, I prefer to use OE Honda parts. They seem to last longer.