amzn.to/37kcE3U - Premier Gear PG-10910 Starter Replacement for Silverado 1500, Sierra 1500, Tahoe, Yukon, Express 3500, Express 2500, Escalade, Savana 3500, Suburban, Escalade ESV, Savana 2500, Yukon XL
amzn.to/48nVSR7 - GM Genuine Parts 12695760 Starter
amzn.to/41taqwC - XtremeAmazing Starter Pigtail Connector Wire Harness Plug for Chevy Silverado GMC
amzn.to/3RL7yIf - X AUTOHAUX Starter Pigtail Connector Harness Plug for Chevrolet Silverado 2014-2018 for GMC Sierra for Cadillac Escalade Replace PT2974 19300471
amzn.to/3tkV5kY - Milwaukee 2767-20 M18 FUEL High Torque 1/2" Impact Wrench with Friction Ring
kokenusa.com coupon code: Danthefixitman10 for 10% off
amzn.to/46WytVz - Yamashita Industrial Research Laboratory Koken 1/2 (12.7 mm) SQ. Socket for Impact Wheel Nuts (Thin) Total Length: 4.3 inches (110 mm) 0.9 inches (22 mm) 14145PM.110-22
amzn.to/46UUZyc - 2960 MILWAUKEE'S Mid-Torque Impact Wrench,3/8",Cordless M18
amzn.to/3vbdL76 - GEARWRENCH 3/8" Drive Micrometer Torque Wrench 10-100 ft/lbs. - 85062M , Black
amzn.to/3GLakGU - Koken Tools 3/8 SQ DR NUT GRIP® SOCKET SET 8MM-19MM - 11 PIECE - RS3450M/11
amzn.to/3taZdUN - Milwaukee 2567-20 M12 FUEL Brushless Lithium-Ion 3/8 in. Cordless High Speed Ratchet (Tool Only)
Just a quick video on a 2016 GMC Sierra 1500 that had an intermittent starting problem. When it was brought to me, and I first looked at it, it started for me several times in a row without any problems at all.
The owner said a lot of times it would take 4-5 tries, and sometimes he would just wait a few minutes and try it again and it would work. The battery tested fine and the connections were all solid and free of corrosion. He said that you could hear a click when attempting to start the engine, so the starter relay and solenoid were working, but the brushes in the starter motor were probably just worn out or a bit gummed up. He said that once he tried tapping on the body of the starter a few times and did finally get it to start, but it was still giving him problems and wouldn't start every time so he decided to have me change it out rather than risk getting stranded somewhere.
The starter used in the video was purchased locally at O'reilly Auto Parts.
Tools needed:
10mm socket and/or wrench to disconnect the battery and to remove the starter heat shield bolt
13mm or 1/2" sockets and/or wrenches for the main starter terminal and for the starter bolts
A socket extension will help to reach the bolts on the starter.
T-15 Torx bit if you plan on removing the inner fender liner like I did.
A Hook or pick tool is helpful for the connector on the signal wire.
The signal wire connector is a bad design and is problematic on this vehicle. Partially because of the non-intuitive design, but also because of the proximity to the exhaust that causes the plastic to become extremely brittle.
The little plastic sleeve covered with heat shield tape is supposed to protect the plastic connector, but it is an afterthought or a reaction to the problem of the heat getting to that connector. It doesn't work as well as it was designed to as even the plastic tube like shield also broke from the heat.
I recommend buying the replacement signal wire pigtail and plan on changing it when doing this and crimping it on. Or you can also just take out the center part of the old connector (on the vehicle) by prying it out with a small flathead screwdriver and pulling it apart and then snapping the connector end on from the new pigtail. You can do this on the truck, remove the wire from the broken connector and then putting a new connector on without having to splice the wire and use a butt connector crimped in place.
The torque spec that I found online for the starter bolts is 33 ft. lbs.
Thanks for watching!
Please Subscribe!
-Dan the Fix it Man
www.danthefixitman.org
www.amazon.com/shop/danthefixitman
Song used in the video:
'Road Tripzzz' by Ofshane
As an Amazon Associate I earn from qualifying purchases.
All other links are affiliate links if possible.
14 дек 2023
