Thank you.just remember TWO OPEN VALVE which is the intake and exhaust valves and the remaining cylinder is on TOP then apply valve setting.pls.share and subscribe.thank you
Thank you for watching.please subscribe like and share. actually they both the same on how to adjust valve tappet clearance but I will do as per your request.
Some other engine for the automotive is the same with your engine.no need to tune up.thank for watching for my video I hope you learned something.thanks pls.subscribe and share.
For Hinomoto c174(engine toyosha cs100, 3 cylinder) is same?which is clearance for intake valves and exhaust valves?are you selling engine parts for this tractor?
I have seen the valve adjustment for a three cylinder engine how will I it be with a four cylinder engine ? Please let me know especially the v243_combine engines
Very good instructional video for easy to understand way to determine piston position /stroke to set valve clearance. You speak at a pace slow enough to comprehend things as they're being said and recap at the end. Best video I found on the topic. Thank You.
My yanmar diesel 3t72sb engine will not move the valves like yours does its different when doing the first set of valves sny help will greatly appreciated
Ok...I will teach you.if you don't know the firing order just follow me and I repeat how to set the valve setting rotate your engine to the right and observe the valve.THERE ARE TWO VALVES WILL BE OPEN and remaining cylinder is on the top and apply valve tappet clearance.(TWO VALVES must be FULLY OPEN) example:if the valves from cyli.#1&2 are open the top is cyl.#3. after cyl.3 just rotate again the engine same action of the valve.you can observe the exhaust valve from cyl.#3 to be fully open and you can see the intake valve from other cylinder is also fully open.the remaining one is on the top to apply tappet clearance.The same on next cylinder.ithank you for watching.i hope will.you understand.
Afternoon sir .....I did put a top gasket on my Kubota ....than it run for about a week but it started to leak oil between the cylinder head and the block again .....does that mean I did not torch it's properly ...or what sir
Boss yong sabi mo na two open valves din apply valve clearance na confused ako?saan ka dapat hihinto sa sa pag ikot ng crankshaft mo na masasabi na tama na e adjust yong remaining cylinder?
dalawang valve Ang mag open,Isang INTAKE VALVE at Isang EXHAUST VALVE at Ang natitirang cylinder ay Ang naka top at mag mag apply kn ng valve setting.hihinto k hangang bumaon Ang valve.
Magaling sir nagets ko na din kse sa tatay ko tumitingin lng ako hndi ko makuha kung pano nya itune up ang d850 namin tinatanggal nya ang glow plug at tinatapat nya sa butas ang daliri nya di ko din sure kung tama ba yon...slmat sa tutorial sir
Boss pano tanggalin impeller ng water pump nyan? Sira na ksi yung bearing sakin. May thread ba ung impeller at shafting nya? O pinipress lng pra matanggal?
Sir paki click n lang po Yong profile picture ng channel ko tapos click mo video at hanapin mo po Kung paano ako magpalit ng bearing ng water pump.salamat sa panood.pls subscribe and share salamat.
@@tractorsmarinemechanic ok sir. Salamat. Nka subscribe ndin ako. San po ba shop nyo? Matanong ko ndin po ano problema pag naghahalo engine oil at transmission oil?
I have a Yanmar 3 cyl engine that looks very similar. Because there is no spring to hold it, the exhaust valve on cylinder 3 has side to side movement of .032" so the lifter is not always centered on the valve cap. It makes noise and the valve clearance clearance is different if it is moved from one side to the other. Can I shim the gap between the snap ring and the lifter to keep it centered on the valve? If I use a .025 shim, it will leave .007 clearance, is that sufficient?
