3 Phase STATCOM for Reactive Power Compensation | MATLAB Simulation 

If you like my work, please do consider subscribing to this channel.Thank you. ru-vid.com/show-UC58DFky5Fm9AxH9UmWHHYmQ

Wow this has really help reduce my final project pressure

Perfect explanation.... You deserve lots of respect..

sir/mam your works regarding multiple areas of power electronics are very helpful for all students and researchers

Well done, thanks for your effort

Yes Sir! I love it, thank you very much.

Amazing!

Nicely presented

Thanks a lot sir/mam . this video helped a lot,. Could you mind sharing complete simulation of UPFC

Thank you so much...can u explain designing sliding mode control for this statcom...your way of showing the program is easy to follow that's why i am asking you....if u don't mind plz explain....

Thanks for the video....

I really like the way you are explaining, please is it possible to use for ieee 15 bus reactive power compensation ?

Thankyou for the video, its been really helpful. Along with the reactive power compensation, I want to supply active power from battery at the time. Can you please help me with the modification that is required to be made? I would be very thankful for your any kind of assistance.

Hey, love your content! Could you please make a video on Modular Multilevel Converter (MMC) using Phase Shifted Pulse Width Modulation (PS-PWM)?

Thank you man

Will you please do a video on compensation of voltage flicker by using statcom

How do we connect the induction motor as the load in this circuit? Will the circuit work for variable load induction motor as well ?

16:36 there is a mistake, you should remove the IDL from there and only leave ID. as explained in the begining of your video. Thanks allot for your time and efford :)

Thank you sir

Excellent. Your job is very good for STATCOM. One question, if you put a three phase fault on it can it control the reference voltage again? If it works for transient voltage recovery or you can modify it I will pay for this. Let me know if you are happy to make some profit.

Thank you so much for your great effort. In my research I need to design a SSSC rather than using the already exists Simulink Phasor type one. Could you help???

Thanks for the great video! It sounds better now that you included commentary instead of just computer screen. Could you please explain how you defined the PID gain values? Was it calculated or just by trial and error? Best regards!

Thanks for the wonderful video. Can you explain why ode23t solver is used.

Sir., I have implemented the same way u have done but unable to get the output..it's showing some errors in the integrator block,.. could u please check?

Hai!! This video is great! Thank you. And can i know how can I select/calculate the value of the capacitor for Vdc? I am trying to make a shunt active power filter for 33kV system. Thank you!

Hello sir, will you tell me the SVC coordinates? SVC works on which coordinates?

Thank you for the video.please can you tell me why you put value 2 with gain in the controller

Hello, Do you happen to have this file? I keep getting the error, running continuous elements and I cannot fix this error.

I have problem with grid current I did same silmulation but grid current is about 4000 A why?

Hello sir... Please show me where u have connected the load?.

thanks for your video sir.. Can this simulation use to mitigate voltage sag under different fault sir?

Great tutorial sir! I wanted some help with how can I add a constant length transmission line in this circuit with which I can simulate the effects of STATCOM at different locations in the grid.

Sir, I am not able to get same active power for load and source but remaining all are correct ..can u please help me out By the way nice video sir keep making videos like this.. I and my friends like ur style of teaching

Respected sir, I request you to please make vdo on extreame fast charging of electric vehicles please sir

Can u give a outline about controllers for inverters and grid.

Thank you, sir, for explaining the STATCOM. but when I trying to simulate my simple STATCOM with a series reactor module in Matlab it does working properly. This means every time I get a different reference signal. I am also getting confused in the controller (means you use that divide Vdc block). Can you please tell me what you think about it,

Can you please specify which version of matlab is used?

thanks sir

Can we make this as Pv statcom yo control reactive power in night or when there is disturbance it fed that power for few seconds to compensate fault.

1. Why you are taken Lg=Linv, could you please tell me? 2. Why you have not used any capacitor at DC side of the inverter

In the last loop of current control before converting to dq axis why are u multiplying by 2/Vdc as we get Vd, Vq directly from them?

Sir can you make bidirectional converter?

How to measure then for 1minute and so , I mean large time data, if sampling time is 1micro second

Thanks for doing my need .. Wat s last scope waveform I mean DC bus voltage waveform? What it is ?

Hey, Great Video.. Learn Many things . Could you Please make a video on STATCOM application for Transient Stability Improvement. or just suggest what changes required in video model so that we can see performance of system during fault condition.

Please Sir can you share the simulink circuit diagram and data ?

Is this STATCOM applicable in 3 phase sytem in transmission 5 bus system and more. If no please guide

What to do for DSTSTCOM

Do you research paper for this simulation?

We need sssc analysis using pi controller

sir I followed all the steps and modeled but VDC is fluctuating, unable to regulate to 800V , the statcom is also not compensating properly. can u please fix this error?

Sir, i have 2 questions 1) what is the rating of statcom and how can I identify it from the video simulation ? 2) Why you haven't used a coupling transformer with statcom?

sir, please can you explain low voltage ride through in PV inverters with simulation?

Thank you so much sir.. how can i talk to you please ?

Hi i tried this simulation but didn't get the output like you can u please help

Sir, in your video, the current waveform has a magnitude of 420A whereas the voltage is 340v. How can grid current be so high? kindly clarify.

Hello sir, I have a master’s project, which is to add a STATCOM device on the 132 kV line to raise the voltage and reduce the REACTIVE power. Is this video useful for me in implementing the project or is there another plan to implement what is in my project THANK YOU FOR the answer

Hey can this compensate non linear and unbalanced load ?

Dear Sir , Can you add subtitles into this video ? please I don't hear your voice

Why my output is not coming

Sir, Can you email slx file. i am trying to simulate but not getting good response.

Sir , 1. If i eleminate the Controller what happens . 2.with controller we are getting spike over there how can we do this simulation to without getting spike

Which matlab version you are using

Hi, thanks alot for this informative video. I have implemented, but couldnt get the results. Can I send you file to have a look please?

Can the same simulation be used for realizing dstatcom ?

Can u provide the ref paper for this work

Bro need statcom with fuzzy controller

Sir can you please do Reactive power compensation on SVC?

Sir can please mention the refference paper or base paper

hi i tried this program...but i am not getting the output like you....

Why 2/Vdc ?!

Statcom and sssc with fuzzy controller

Can we simulate STATCOM with out controller ....

Sir i need this simulink

Sir can you send me those simulation model file ???

Output is different

sir please send model in comment

Sssc facts controller

Dear sir, could you please provide your email, i have some query.

kindly sir need your help share email now

Why 2/Vdc ?!