Part 2 of Bi-toroid, Eric Dollard, Jim Murray and GBEM inspired 3D 3 phase transformer that I hope to turn into a magnetic amplifier and send into self loop power oscillation.
It is highly likely the reason why primary power drops off a little when a load is applied is due to your load causing an impedance match, for example all coils have a specific resonance frequency, if you drive a coil at the wrong frequency "that is a mismatch" by adding a reactance load to the circuit you are re-tuning the coils resonant frequency and hence lower power is drawn, if however you had already tuned your frequency that your driving the coil and it is optimized for low power drain, then applied the same load then you would see a power increase on the secondary drain. The same principle is used in Radio circuits when optimizing the SWR (Standing Wave Ratio)
Hi , it is my privilege to subscribe in your channel , i do love your videos , i am not a scientist or know much a but what you do , i like to build some science projects , but i do like your personality , manner and what you do , you do make me listen and think , may God bless you and what you do thank you
fyi, the input power decrease when you apply the load is expected with any transformer. When you draw current on the load side it creates is own field that opposes the current in the primary causing it to draw less current.
Hmmm, you may be correct on that point. We'll see how it goes. A gap is easy enough to add but I wanted to stay away from it because I want the core to saturate and become a magnetic amplifier.
ZeroFossilFuel Hi :) As you are going on this direction you might also to check out on Gabriel Transformer in PESN. It is directly related to what you are searching for - the closed magnetic loop of Lenz force into itself on secondary coils. Cheers!
If the coupling from the primary to the secondaries is only 34% then the coupling between the secondaries is only 34%, do you notice this is approximately a third of the ideal 100%? Why a third? think about that.
@Zero, if you want to speak to Jim Murray about his alternative energy research, it can be arranged. I just interviewed him on Saturday and I am going to upload the interview to youtube this week. I was fortunate to get a walkthrough of his laboratory, too. Very cool.
Zero as much as the changes have pissed me off too, I am getting a lot more hits on my channel. I just picked up 10 subscribers on my gasifier stuff in the last two hours today so we'll see.
Is this is a Wye-Wye or delta-delta 3 phase 3 way monocore ? Have you tried using magnets as a core or ferrite? I have found some pretty extreme results using a very similar setup. I took 3 threaded ferrite rods and bolted them to two drilled triangular 1/4" iron plates, loaded my bobbins on them and powered them up with 208 to each winding on my primary, and loaded the secondary to get exactly what you have said. When I place my 3 phase motor into the circuit, it fires up, dropping the load to 1/3 less than the load consumed on the secondary if that makes any sense, and I am running at nearly 57% efficiency. The windings on the primary are delta, and the motor is wired in delta to the secondary. I am going to try wye on both the primary and secondary to see what happens after i rewind my coils to try to get more efficiency.
Haha yep forget to turn on the mic! Haha so manny times I'm recording when I think I'm not... And not recording when I think I am! Man that gets old! Lol also need a link to firepinto's youtube in the description! And last thought put a small washer in-between your wood and your spool for less resistance. Good stuff!! ~Russ
Let me ask you a question. I realize that what you have is only a test coil and that it isn't perfect but what was the insertion loss compared to just hooking straight to a load? I hope that made sense. Thanks.
Perhaps the decrease in primary draw with secondary loading was due to a variation in the reluctance of a saturated core, saturated by the extra flux produced by the current loaded in the secondary. Variable reluctance transformers were the power-transistor before transistors were invented.
If the power decreased in the primary when the secondary was loaded, is it possible that the inducive reactance increased in the primary due to the loaded secondary?
The originators claim "adding a load decreased the input." we know that most detuned to tuned will follow a curve. We have been told that tapping a negative entropy is possible others say impossible. Studies show that fuel reformers raipdly speed up or strip off hydrocarbon chains using plasma. diy gliding arc.
Hi there I have been following your post for a long time now and have always wanted to subscribe just never logged in to do so. That done. Love what you do ! Now I've been wondering if you have you forgotten about hydrogen ? And do you think with these experiments especially with this try core, to combine this in the future. I'm working on (note with very little electrical background and youtube as my friend) on hydrogen using, high volts, low amps attempts at resonance and thinking in the direction of drawing up n chart for electrolyte concentrations and resonance for a certain spectrum and then by using the amps drawn and flow of electrons to determine which frequency range should be used. And then using a rely let it go through a small control box and let it run. I got the Ide from amateur radio, im a radio amature and when I build and tune my antennas it needs to be cut to a resonating frequency but we cover a whole spectrum with one antenna, I also have multi band antennas and when I tune my frequency its automatically choses the right antenna for the frequency im broadcasing in. Sorry for the bad sintax an grammar Im Afrikaans and English is not my best language. Luckely there is spell check but expressing exactly what and how I want bit more challenging.
No worries. Afrikaans is Charlize Theron's first language too. {sigh} I'm a ham too. Have worked Capetown South Africa several times on 20M SSB using my multi-band OCF inverted V Windham dipole. Have not forgotten about hydrogen. Just have no time.
Is the baling wire "coated" in some way, this seems to be important to those developing the Bedini versions of filled cores, although I'm not sure if this is also your intention, but thought to mention this. Another worthy point, based on Ed leedskalnin's work, he seems to be indicating that the magnetic "flow" is circular or spirals around the conductors it is being induced into, although I'm not sure of the real significance of this, it seems to be overlooked by most shooting for what it seems you are in your coil performance! BTW... the current drop in primaries when load increased in secondaries is prevalent throughout the pulse motor/generator designs. GO WITH IT! Also there are huge secondary spikes being detected/reported in some that possibly can be channeled via diode into a recirculating or radiant capture circuits that can either increase efficiency or be used to charge batts or caps... this is something I am about to play with myself! Good luck, and keep posting updates on those results!
Hi,. Like your,. Video,. And your "office" work,. if you ever create a hot to build a model of some kind please do i would be lovely interedted,. to buy and purches,. how to plans.
Your stats didn't improve because of google+. They improved because you did the energy convention. Google is still a horrible organization that has significantly marred youtube.
Dude, you are missing the whole backwards flipped upside down underhanded and deceptive practice behind this change in RU-vid/Google, beyond the initial outrage due to how many thing broke, until we all got our individual bugs fixed with the help of MANY USER contributions, LEAST of which came from Google or RU-vid help for that matter, but our peers are the one who identified the fixes for most of these bugs...and all of those things you mention being "perks" although previously unavailable for the most part, DID NOT REQUIRE this merge in order to be put in place. Although they may make it look this way, the ONLY reasons for this change was, yes as you said, the one stop eaves drop, but it is MUCH more than this, and most people do not realize. You see, along with "unifying" the log in for all google services, this also now REQUIRES a Google+ page be created for EVERY user, which is Google's answer/version to/of facebook (not sure which is the lesser evil the CIA's facebook, or the Corporate conglomerate's Google plus) and what this does now is, first and foremost, seriously or completely reduces security in the anonymity (not sure this is a BAD thing, at least where ne'er do wells are concerned) having had a "USER NAME" which also is/was the "channel name" to utilize like many forums, allowing a little creative expression as well as getting to keep one's real name out of it, but then you have lost channel isolation too, whereas previously, if one were specialized in a few specific fields of interest, they were easily kept separate, and no one could tell when the same person was uploading to multiple channels, however the moment you follow your comments/messages from RU-vid Videos, and pick up the discussion on Google Plus, now EVERYONE can see WHO you are and through following a number of discussions of similar interests which may also not be a bad thing but getting back to the "big leagues".... does everyone realize that AD PRICES are based upon "membership" and exposure through "impressions" and clicks, on all ads throughout Google plus, and their other services... and by inflating this "Plus" membership through the all users requirement of use ANY service HAS to have such a page/account, and in this way they are drastically driving up the cost of advertising by inflating viewership, FALSELY, because the ONLY reason I have a google plus page is due to requirement, and will likely NEVER actually DO anything with it, but yet I "count" in their overall membership, and contribute to the higher prices of advertising on Google's services....and guess who will be BUYING that ad real estate?? That's right, every struggling cyber mom and pop or individual shooting for a low startup business with a high potential for exposure they could NEVER manage in their town, let alone develop anything nearly as quickly, and WHO ultimately will be PAYING for these inflated advertising prices??? US the CONSUMERS...because ALL business must pass on such expenses to their customers, so for the few benefits you mentioned look how much is ultimately being sacrificed, as well as losing our ability to remain secure in our anonymity. Along with even further unifying their tracking of interests, circles, surf habits, and shopping histories, that already Google search has modified their algorithms that NO TWO PEOPLE will get the exact same search results for the exact same terms, which basically is "Filter discrimination" Go ahead, get on the phone with a few buddies and do searches using the same terms, and aside from "targeted local businesses" based on geography, you will NOT SEE THE SAME RESULTS, and in some cases quite drastically different ones. I just felt this was not very clear in your opening statements.... NOW I can settle back and actually watch the CONTENT of your video! LOL! Namaste'!!
If you can make free energy, then why are you not powering up your shop & hole house & \ if you can make free energy, you would be to busy hooking you friends up & other people, Please answer all Qs
that Is one hell of a Stupid system you have to log in Twice to post a Comment??? I just wanted to let you know I am in Canada and I would like to know what happened to your contributor in US with surge technology. There is a Rumour that he was Murdered. If not dose he have a Production Model you can buy If not plans and Parts.... seems like a better Idea this is what Paul is doing for GEET fuel processor.