Wow, awesome clip! Had to clean throttle bodies and MAF since my 2010 370z roadster was running rough. I can guarantee they were never cleaned by previous owner because when I started cleaning, they were both super dirty with crud. I wasn't quite sure why the idle was so high after I cleaned them until I saw your clip...didn't know I had to do the steps you provided to re-learn throttle bodies and pedals to get it back where is should be idling. My Z car is running great thanks to your instructions. Again, outstanding instructions, thanks!
My throttle body was insanely bad. Like thick thick coating. I changed my intake filters too and My car is driving so much better. It felt chocked up before. Thank you brodie 🙏🏽
Never touch/move the throttle plate with your fingers.. have something or someone step on the gas (not with car on of course) as it is electronically operated and it might mess it and you will have to re-program your car. Learned the hard way.
Thank you! This was helpful. My G37 6MT has 78K miles and my driver's side resonator had broken - causing it to run too rich and throttle rpm at 2300. I repaired the resonator, (JB WELD) and cleaned the MAS and the throttle body. Huge improvement - this breathed new life into it. acceleration is smooth and linear again. I have way better throttle response than I did even before the resonator housing cracked.
Thanks a bunch bro, this is definitely the best guide for VQ37HR owners looking to clean throttle body and MAF Sensor and gain maybe 5hp lol. The recalibration took me a while but im lowk slow, I have a G37x sedan btw works for any Nissan/infiniti with the VQ37HR
i recently did this since i had a check engine light/service light 💡 did everything you said in the video but my car seems to idle back to normal without resetting the factory .. i’m at 600-700 idle car runs amazing since the cleaning definitely needed that
My rpms go high like normal but it goes much slower, got a pending code for p0101. (2013 g37x) Hoping i just gotta clean the maf sensors for now. Gonna clean the throttle body anotherday
If your car is like mine and the bolts won’t undo on the strut bar, you can remove the tubing etc. to access the throttle body without taking the strut bar off.
Just got a 2012 Z and your videos are answering so many of my questions and concerns. Keep it up man bc you put out good quality videos for being a small channel rn. Hope one day I can say I’ve been here from 1k subs🫶
I have an 09 370 with high idling, and I’ve had the p300 code, swapped the plugs and coils, checked for vacuum leaks and cleaned the mafs, this is my last hope lol I’m worried about the relearning process looks tricky
Did you end up figuring it out? I’ve also on the same boat at you & have swapped the same stuff you swapped and still haven’t figured it out. However yet to try this! We’re you able to fix it?? Please lmk!
Does it work on 2007 g35 it’s a hr same body style and dn same parts all around as the 37 except the motor but I wasn’t cleaning my throttle bodies I was replacing them
I’m showing code p1016 p100a and p100b, everytime I turn my car off it makes that robotic click, whether the ignition is on or just the car. Can any one think of any reason or help me out
I did it followed ur instructions but I have a question after the 1st start after the reset the speedometer was going up and down once I did a 2nd start it did but way less very little should I be worried?
Can I do this and avoid the resetting because I have a tune on my 2009 370z but idk what or who did the tune because I bought it like that I just got a code pop up saying P1421 which is a cold start code and I think my best solution is to clean the throttle bodies instead of replacing them because I don’t think the previous owners cleaned them
My 15 Nismo SES light came on and I've replaced the MAF cleaned the Stillen air filters and disconnected battery but the light keeps coming on throwing the codes for MAF P0101 and P010B any idea what else it can be? At first I tried cleaning the original MAF but light kept coming on so I got new MAF for both sides and light keeps coming on
My throttle body shat the bed and im replacing it. Thanks for the vid! You think if I'd of cleaned them it wouldn't of died on me? Or that's something else .. im at 200k km
Make sure car is at operating temps and battery is strong. Turn off ac and radio to reduce energy usage. If you’re following that and the rest of the steps in the vid then it should work. Maybe your timing is off? Lmk how it goes
Recently my car has code p1239, whichI think is a throttle body problem. I wanna try to clean and reset it, but I have admin tune, and I was wondering if I do the relearn and reset, will that mess up my tune?
I emailed the admin tune, and they said it was fine and wouldn't mess up anything; that code just popped out randomly. My car drives fine, so I did not clean the throttle body.@@cartercarstensen374
That’s strange, the light may have gone out. Maybe try following all the steps still and see if it works. Just try to time it good since you won’t have the light indication
fully depress the accelerator peda Wait 20 seconds and Fully release the accelerator pedal within 3 seconds after the MIL turns ON (((((((((( NOT RUN in wait 3 seconds in stop MIL ) and ON