5 axis CNC machine build Pt.2 

Really liked the musical interludes. Your machine is becoming awesome!

Very well thought out. I like your mental drive. You seem to always have good solutions. Nice Job!

Best produced video yet! Your ambition and drive is inspirational!

It's looking good I can't wait to see it running. 5 axis is a dream to have.

I keep thinking of what body to mold over which chassis. I love the look of the Mclaren. I also think the veloster has a good slope for a wider race car look. I love your work man. It’s very inspiring !

Your channel deserves more views. Its really inspiring! Most things in life arent rocket science and are plausible to do yourself as long as you try. Keep up the good work man! Greetings from Sweden!

"only the peasants have Philips head . . ." Smoking hot build bro

Did you get the 5 axis machine done?

Going great man! Love ya work!

NATHAN NEXT CHANNEL INSPIRE THE WORLD....👌

A few suggestions you need to check if you rails are parallel... it's a good idea build some adjustment suport plates in your gantry to adjustment the gantry for twist ie to tram your xyz. Your x axis rail could have be installed farther apart..from lower rail. are you going to use clear path servo for xyz???..you should think about it to prevent losing step on a 5 axis.

This is very inspiring work, you've got a great grasp on what needs doing, very impressed!! Been loving this CNC build, haven't seen any updates in over a year, but I see you bought a Fadal Mill (which was also another great video, the rebuilding was awesome!). Have you finished building it, or did you put it on pause or decided not to finish it? Would appreciate an update as I love what you've done so far and would love to see how it ends. Take care and congrats on your shop man, looking damn good!

Awesome to see another video. Keep em rolling man! Have you considered a magnetic base indicator dial on an arm that you can lock or is rigid to run on one rail to align the other rail so is spot on? I'm looking to improve the cheap Chinese lathe I have and make into a mill (new bearings, right angle plate with vise, lock carriage, etc.) and one of the things I'd like to do is make a longer bed and ways and have watched some made even from cast granite and epoxy. I'm almost thinking using an old engine block so is cast iron and maybe fill with granite and epoxy. Then probably going to use a free treamill motor and controller... ok... shit... I'm rambling. Keep us posted! Awesome projects you got going on.... smooth.

Torx master race! Stopped using hex years ago because it always rounds the edges on both the tool and the fastener

Awesome man! Keep going! Best matt.

Keep mobbin bruh, your vids are legit

just you ever finish this thing? We never got to see finished videos of it?

Some advice from someone who assembles prototypes get all you screws in then tighten it. Other than that good job

Nice video! What are you shooting the video on? That shot at the end looks really good with a nice frame rate.

4:13 to get 2 X rails paraller and level is easy,but get z axis squared for that. you cant use dial indicator and move z up down. needle not move even it move 5 degree LOL. bcox linear move traght you measure one point needle not move xD you need move needle not axis so you need another axis for dial LOL

Ola Inspire , ótimo trabalho ! qual será a área de usinagem de sua maquina ?

wait a sec so oyu are letting your y axis just on just a linear rail with 3 blocks per side? ow is that even stable when its that freakign high

Any update of this?

awesome

Hi. Your project is perfect. I know that it has been completed a long time ago, but I would like to know if you could indicate the files of the electronics and software used. Thank you very much and success to you.

Can you give use a cost up date on how much the upgrades cost...as well as some idea the total build cost..this far...ie the new z axis aluminum plate cost...linear rails...ballscrew... motors extra. You cost for b ,c axis build.

what happened . did it work ?? where is next episode of 5th axis ??

it to bad you never finish the video on building your 5 axis router.... would have been some great content to your change.

Why would you push that gantry mount and not make vroom vroom noises

Dude you're crazy for hand tightening all those screws with an allen wrench! Simply secure the screw bit to a drill with a clutch and never strip the heads again and save yourself a ton of grief!!

Nice job ! It looks pretty nice and sturdy. Are you using HGR 20 linear rails ?

hey man your 3 axis cnc machine is very cool. i am looking to buy a pre built one or potentially buid one myself. would you have any references to where i can find a guide or by any chance we can work something out and you can ship something out to me?

What is the cnc machine built from 6061 t6 aluminum?

Could you teach how to create a motorcycle model in rhino? I want to learn it

In the next episode..

Did you ever finish it? Want to sell one?

you never finished the series on your 5 axis build.... disappointing not see how set it up and calibrated it

给我的 第一感觉，散架.散架..！！！！！！

Hey can we get a update on the project

Part 3?

Shre project

done baby.... moron. ------- oh. the linear rails sounds like a steam locomotive.. perfect!!

where is the next video ???

Update your build pls

Can you sale this 5 machine

Nice, but you need to learn to weld