I agree with this list, as an alarm guy. I recommend the Klein tweaker as it has 4 different sized tips in the shaft and I do use it almost daily. Also the Klein 11 in one screw driver, also has multiple size bits that can be quickly swapped around. The long handled snips/cutters are essential for cutting cables and wire, but at times I also find myself using a very small pair to snip just one small 16g or 18g or even smaller wire thats bundled together with a bunch of others. Having the small pair allows me to cut just one wire precisely, and cable ties that the larger pair is harder to work with and ensures I am cutting only what I need to and nothing else (very important). HVAC units often have big bundles of dozens of wires that run together. So even though we work with primarily 14-2, or 16-2, and 14-4 etc, there is a use for them. Yes you will absolutely need a multimeter as well, but starting out you start realizing the tools you need and begin to aquire them as you go. We use dozens of tools on install jobs, yes you will need all of them at some point, but to start out you need the essentials listed here, and you should have a multimeter as well. I use my flashlight and head lamp a lot as well, I recommend the headlamps you can get on amazon, rechargeable and motion activated on/off feature. This allows you to waive your hand in front of your face to turn the light on and off all day without searching for the button.
Switching from electrical apprentice to low voltage technician. I believe low voltage technology is only getting more advanced and wide spread. Plus I feel I’ll find myself in much cleaner situations compared to when I was apprentice electrician. People have gotten on my back about losing what I’ve built in electrical hours, but I’m looking to do what I feel is best for me and my future.
Leaving the corporate world to become a low voltage apprentice, should be starting soon. And I am absolutely stoked for this new beginning. Thanks for the tips, gonna go buy some tools this weekend so I can be ready for the call.
Low voltage AV installer here.. I carried the same snap-on screwdriver for 20 years, but just recently (3 years ago) switched to the Rolgear 15-1 ratcheting screwdriver. I find that I like the 3" bits for getting down in tight spaces that I sometimes couldn't with the snap-on... Thx for the video!
Thanks for watching and for sharing you input on the Rolgear. Had to go look it up and it seem like a great screwdriver that I might need to get my paws on one. I wish you could store & use standard 1" bits. As you know lots of products come with various security style tips and it's nice to keep the ones that "you" work with mostly in the handle of the snap-on. For example, Axis uses various Torx screws, so I like to keep various Torx's (many with the center holes) in my handle. Nothing as unproductive as being up on a roof, lift or ladder and having to go back to get a T25. 🥴 That being a potential obstacle for me, I am still am very intrigued, especially since you used to use the snap-on!
@@AccentAlarms I still carry the snap-on for my 1" bits, but 99% of the time I reach for the Rolgear. I also picked up 3" security torx bits from picquic that will fit in the handle of the Rolgear.
@@donniemccrorie19 lol I almost ordered one this morning to try out. Maybe I'll give in to the urge over the weekend. But, I'm really trying to minimize my life - not carry another something. 🤣😂🤣 I say that and always end up putting more tools and other stuff in my trailer/tool bags & belts. I'm not very good at the minimalist thing! 🤔🙄🤔
I was a MeCP certified installer back in the day , today I’m a Nicet 3 fire technician , I have to disagree on the multi bit drivers bits fall out and damage electronic boards . Always use a solid driver I like your channel and when I saw those crimpers I knew you were old school I have same ones the difference is I shaved the cutter off as to not damage wires in the background, good luck and keep posting videos.
:) Appreciate you taking the time to watch. I can sure see bits falling onto boards. I use the Milwaukee tips and magnetic holder and having seen that with those, but I have some other tips that do that all the time. Funny, I got my start in the Navy as an Electronic Warfare Technician (Anti-ship missile defense on a Carrier) and when I got out I ended up getting MeCP. That was a year or two ago. 🤣
I would add a few more tools. Hammer drill. Bits for wood, metal, and concrete. Tape measure. A good pair of linemans. I like Klein with the crimper and the Commercial Electric with the crimper. Strippers for solid and stranded wire. I like the Klein yellow and red handle strippers. Klein 14 in 1 multi bit screw driver. You get small phillips and flat heads plus a few small security bits. Markers, for labeling wires. And electrical tape, lots of electrical tape. We use white for wires and I use orange to mark my tools. And a good tool bag or box to put it all in.
I'm partial to Klein myself, Klein 1005 crimpers, Klein Kurve wire strippers, and the Klein 4-1 technicians screwdriver. Typically I carry my Klein 11-1, but have taken a liking to the Wera multi bit screwdrivers! Thanks for the videos sir, I really enjoy them!
I'll have to take a look, I've got more than my share of Milwaukee tools so I suspect you could be on to something! :) Thanks for the input and follow!
I'm a comercial service tech for a alarm company. My 5 tools are multimeter, multi attachment screwdriver, wire strippers, tone generator, pocket full of wire nuts
I like the small milwaukee side cutters over the snapon ones, cause theyre smaller and have a crimping spot behind the cutter, making it easier to crimp dolphin/b-connectors.
Just had a job interview to become a service meter technician! I've been an electrical apprentice for about a year but due to lack of experience companies are reluctant to hire me so hopefully this will help out!
Started two weeks ago and my most used tools in order are Dewalt dcd791 drill/driver, klein stripper/crimper/cutter, and hammer. I do mostly pre wires and trim outs though, not installs.
👍 thanks for watching. You're right on point; the tools will vary depending on your tasks. I purposely, have a few key tools that I find that I use frequently and adjust based on what I plan on doing.
What about a Flat head screwdriver Lv1 cut out tool Multitool Razer Channel lock Puncher Multi meater Small Screwdriver set Toner (or beeper tester) Sheet rock knife Stick/snake Tape Wire stripper Metal cutter Hole saw Step bit Metal bits Screw gun Drill Space bits Insert (female) crimper Rj-45 criper Rg6 criper and striper Stud finder Pencel Hammer Tape measure Hamer drill Grinder concrete bits Space bits I prefer Klein tools and Milwaukee for bits I like Bosch
I am studying Level 1 training for ESA electronic security. I purchased access to online training. I wish there were more videos on the field made here in the U.S.A. There's hardly any. I'm very new to learning the science on electricity, it's a struggle. I would like to know more about the on the job training. I only see vids about fire tech, but I'm guessing that is second level.
There isn't much in the way of easily accessible training, however that's amazing for job security as it's all proprietary. You don't need a college degree, you just need to start in the field and you'll get paid training by companies.
Thanks for the feedback! I know a lot people who agree with you. I have to admit with all the tools I carry around and own, I don't even have a pair. 😮 Maybe I need to give them a chance, I"m more of an ideal strippers kind of guy. 😃
Linesman pliers combine two of the tools you have. But you also forgot a good meter. I’ve successfully been troubleshooting for years without one but having that extra resource makes it a million times easier and more efficient.
Thanks for watching and pointing that out. You a definitely correct, a meter is required! :) I made an entire new video based on your comment about having a multi-meter at ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-_dEX5yaR4B4.html I personally wouldn't use lineman pliers for low-voltage work, a bit too large for smaller gauged wires. Thanks again for watching and I hope I didn't butcher your name on the other video. :)
I only install security systems and so I mostly work with station-z wires and bean connectors. I think if that's all you do, then you can just use the crimping end of your stripper to crimp the beans. Fewer tools = more efficient. Also I think a switch-bit screwdriver filled with impact-ready power bits is a must-have.
Thank you for sharing your opinion, but I would respectfully disagree. Strippers are not the correct tool for crimping. I've seen more than my share of failed connections due to poor quality crimps. I would highly recommend getting a pair of either ratcheting or long handled crimpers to provide your clients with long term quality connections.
@@AccentAlarms I agree, had to redo a whole Alarm Panel Vista20p with four Zone Expanders because the Tech that installed it used his strippers to crimp the Beanies.
I just left an interview and I'm pretty excited. I know it's commission based, but I've an important question that might keep me from starting this job Am I going door to door as if I were a salesman?
Good point, one of my early videos and I should definitely replace "you need a pair of these" with "you need a pair of quality crimpers such as these Snap On 29ACF's"
Thanks for watching. Five or even six tools will be never enough, but more of a place to start. FYI I pull a 20-foot trailer so I'm guilty of having slightly than five tools. 🤷♂😅
Idk if I would use dykes for beanies if you're not experienced using them you might cut them then you just wasted a beany, used a small pair or plyers or the blunt end of strippers
I would not use dykes for beanies regardless of your experience. I always recommend the right tool for the job; and we all know that hammering/pounding tools are pretty much anything with a flat edge. 🤣😂🤣
THEGREATHELP that truly depends on what part of the world/country you are in. Your best source for that chunk of information would be to call a few local lo voltage companies in your area.
THEGREATHELP TheGreatHelp, that truly depends on what part of the world/country you are in. Your best source for that chunk of information would be to call a few local low voltage companies in your area.
The greenlee UTP/Coax cutter/Stripper PA1119 (aka the Paladin Tools PA1119) is significantly better than any other similar tool I've ever used. (The PA1116 is equally good for UTP but doesn't do coax)
Good point. I could see that if your doing inside work and mounting to wood or drywall, but most of my work involves mounting devices on steel posts and plates. Thanks for watching!
The Mega pro ratcheting screwdriver is my favorite. Still want to try a snap on one though. For a ratcheting stubby go with the vessel ratcheting ball screwdriver. Never use kliene's or Irwins cheap taiwan ratcheting screwdrivers, you're better off just using a normal screwdriver if you are going to use those.
I wish I could find some solid training as well. Is there anything out there? I am also quite new. We do fire alarm, mostly vista 20p & 2gig for burg. Need some guidance on where to go to supplant on job training!!
Thanks for watching! I would check with your local distributors, they often have training classes. They should at least know what is available in your particular market. You may also find that you can attend some training at the trade-shows.
I do everything under the sun that involves Low Voltage, been doing it for five years. Besides those you listed here are a few more. Hemostats Side Cutters with a crimp on the towards the handle, I prefer the Milwaukee 48-22-6108. Auto-ranging Multi-Meter. Doesn't have to be professional grade, just enough to check voltages, resistance and continuity. I use a OWON B35. Hammer Drill/Driver, I mount TVs a lot and I attend to run into some sort of Masonry or Tile. Typically when a TV has to be mounted over a Fire Place. My co-workers laugh at me but I sport Ryobi's Burshless Hammer Drill P1813 Rare Earth Magnet, Used anywhere for Troubleshooting Alarms to locating Metal Studs on commercial sites.