New firmware and wizard on the Jack pot and transmission parameters set and corrected. #aftermarket #fuelinjection #howto #chevy #testdrive #impala #jackpot #acesfuelinjection #tuning #transmission
This car is a customer car just needed a little help on a couple adjustments. Got it just right and made him super happy. We are going to hit the dyno with it soon.
Could you do a video on the Advance Tuning software with the jackpot system dialing in the VE tables and setting up spark tables ect? I think that would be helpful for a lot of folks interested in this system since the resources are limited.
I am covering the basics before I start diving deep. What you wanna see first? It’s all on the list but I have seen more quick shifting transmission stuff needing the info out there.
@actionvulture5251 I've got the base tune down but just looking for more detailed info on how to actually take the learn tables and transfer that Info into the VE table. Essentially a deep dive on how to actually tune within the software rather than rely on the learning function.
Well, I purchased a Killshot and now I’m in the process of consuming all the videos you have made. Thank you so much for the info. I had planned to continue to use my msd 60143 to handle spark just because I am also on the older side and want to stay with the things I understand. Am I correct that I will be using the grey tach in on the kill shot, connected to the msd tach out?
Can You use the Killshot with a Baumann quick shift 2 transmission controller, The controller needs the tps signal wire for monitoring for the trans speed sensor thanks for your time....
I split the killshot TPs sensor wire for a controller and it lost its mind. Made cursing unstable and idle erratic. When you split that signal you either a rail to rail op amp so it don’t back feed or a separate TPs sensor in line of the cable. Summit gots them.
Would you say the jackpot is comparable to the holly? I'm looking to get a system this weekend, but just don't have faith in this system because of all the complaints.
Yes it is close to the application of the termx or xmax. As for negative comments, who ever posts good news on a help page. From my end I see a lot of install and setup issues. For a third party answer call one of the remote tuners and just ask how they feel about it and what they see. My opinion does not matter as much because I run the Aces R&D department.
@@actionvulture5251 I've seen a lot of people say it runs rich, but I don't think they're setting the fuel pressure up. Know you need to put your wheel size what gears you have, etc. all that could play a part to anybody's not doing it right you know can you give me a discount? I'll buy it from you right now.
Is there any way to wire up the factory gauges to the setup and correct speedo accuracy and such? Looking to do this setup on my 90’ suburban with a 5.3/4L60E swap and really wanting to use the factory gauges. The speedo is electronic on the 90’ and all the other gauges just used sensors. You think there’s a way I can make this work? ACES’s website isn’t very clear on this and just acts like it can’t be done and that is why they have the display to monitor stuff
Hey Action, got a Killshot on a Buick 455 with a fair cam. I've been running the thing for a little over 2 weeks now. I only have one issue with it. Whenever I accelerate or deccelerate too fast in first or second gear, the car start stuttering and the RPM is jumping from, say, 2000 to 2200 rpm. It does so up until I accelerate a little more, or when I completely leave my foot off the pedal to deccelerate. Anything I can do in the fuel tab to help this? Or perhaps in AFR? The system is still on learning mode btw. Besides this I am really enjoying the system. Sorry to bother you here, I ain't having a reply via the tech support email of Aces. Thank you!
You might try to clear out the learning data and upgrade to newer firmware. If you got older stuff in there the learn table is different. It used to be by percent now it does it more accurate by using ms or pw. They are fixing to drop the new new firmware I got to try today and it has the reading for oil pressure active. Get that new firmware and run through the wizard and see if that helps. Let me know
@@actionvulture5251 Thanks for the heads up. I fixed 95% of my issue using working in the tabs, but I'll gladly update the system. Will the update with oil pressure include the possibility to display fuel pressure as well?
@@actionvulture5251 never knew to set the VSS percentages not sure if I feel the shit in the trans when I’m supposed to, the folks in the Aces group told me it’s more to just setting the perimeters in the jackpot handheld
Just got one of these and swapping from a terminator x! Drawing a blank on the power_en wire to alternator its say it gives 12v to alternator for power do i need a resistor pigtail or is the system already set up abd i can terminate the wire and play?
Anyway I could contact you would like to pick someone's brain who has done this system. Having small issues with mine and im struggling breaking the terminator x mindset lol
Thank you for making this video. The way you talk or how you make content does not need any adjustment at all. And who knows, the person that bitched about how you talk, has NEVER had the motivation to makentheir own informational video, and probably sounds like nauls down a chalkboard. So fuck em buddy! Keep being yourself, to be cliche...lol. Sorry for the language. But thank you for the video
Thank you for enjoying the info. Some people only want the negative I am just going to keep being myself. I did have an offer from a production company to make a professional level video on an install so I might camp it up some.
Happy to hear the advice. You should hear the noise inside of my head when I am thinking of what to say it’s like tin cans in a tornado of words pictures and information.
😂😂😂 That's what makes you unique. You unique. I'm sure there's a better way of saying that I'm just not smart enough to put it together @actionvulture5251