air conditioner set: amzn.to/31lmH96
good other AC set: amzn.to/2CLw2gj
great Bosh alternative AC set: amzn.to/2A5w6X9
good alternative AC: amzn.to/2NKfV53
ac rubber mounts: amzn.to/2I7lNUn
level: amzn.to/2uB4CCp
folding ruler: amzn.to/2FNvFRp
Boschhammer: amzn.to/2FLG1Bl
drill bit set: amzn.to/2WwlndV
wet & dry vacuum cleaner: amzn.to/2QNtJhF
rawlplugs: amzn.to/2HNqy60
screw set: amzn.to/2FO4czf
compact bosch drill: amzn.to/2CFrbuf
long masonry drill: amzn.to/2FL7zqn
concrete shank drill bit: amzn.to/2YyDGky
insulated screw driver: amzn.to/2JQm3cL
torque wrench: amzn.to/2JSsNqt
crowfoot set: amzn.to/2JUJphk
⅜” wrench adapter: amzn.to/2JQwMDQ
adjustable wrench: amzn.to/2FEnKol
duct tape: amzn.to/2HZl3Ap
pipe insulation tubing: amzn.to/2I6NNXQ
insulating foam spray: amzn.to/2HPG6WH
different pvc pipes: amzn.to/2K0zSWe
wrench socket set: amzn.to/2KT0irM
wall cord cover: amzn.to/2I2wWFY
vacuum hand pump: amzn.to/2CMjzWH
4k Gopro: amzn.to/3878qAx
Gopro head strap: amzn.to/2XzhR7A
Gopro bicycle mount: amzn.to/2xDfK3l
Tripod: amzn.to/34NcAvm
The links above are affiliate links that belong to Amazon or Ebay partner programs. If you buy something through these links, I will receive a commission, of course without you having to pay anything more. Thanks for your support!
For contact options and links check my channel info,
Thank you for your interest in my videos!
transkript: Hello here is Carl the landscape guy. In my new office I’m installing a split air conditioner system, that will be used for both heating and air conditioning. The model I chose is a 9,000 BTU 2.6 kw precharged inverter kit. Among other things, the manufacturer advertises that this system saves energy and is very quiet. It has an antibacterial coating on the fins, works with a new, environmentally friendly refrigerant and can be controlled via WLAN with a smartphone app. This system comes with the coolant prefilled unit, 9 feet of refrigerant piping, and small parts such as a feedthrough tube, insolation tape, sealant and rubber mounts. There is also the outer wall bracket, which I will show you later, when it comes to the assembly of the outside unit. Then here we have the indoor unit, which is very light. It comes with a cable that will connect both units. It also includes the manual, the remote control and a wall holder for it. Both devices seemed to have been well-packed and arrived undamaged. This is the back of the wall mount. The indoor unit will go on this brick and concrete wall. I measure the distance between the holes of the wall bracket from the outer edge of the unit. Horizontally, the plate is slightly adjustable. A minimum distance of half a foot from the ceiling must be kept so that the air can flow properly. I draw the height of the upper holes with the help of a level. The wall bracket can be easily detached from the plastic unit. It clips on at the bottom. I use the bracket to mark all holes exactly. I use a 5 mm masonry drill with a Bosch Hammer to make the holes. When drilling indoors I use the Kärcher wet & dry vacuum cleaner to catch most of the dust. In case you are interested, I will link all tools below in the video description. By the way, the rawl plugs and screws were not included. Now I will prepare to drill the 65mm hole in the wall. First I mark the position of the hole. You will find the distances for the hole in the installation manual, they are different for each unit. I use a long masonry drill to pre-drill the shank hole. I make sure that the hole is angled on a downward slope. When the guiding hole is all set, I set up the 65mm concrete shank drill bit and start making the hole little by little. Every few inches I empty out the drill. I drill from the inside out as far as I can get. This wall is 40 cm thick. You can get a longer drill bit or drill from the outside. Thanks to the guide hole, I know where to drill. I am making sure the inner and outer holes are matching up nicely. This drill bit wasn't that expensive and it worked pretty good so I will link it in the description. Now, it’s time to go back inside. I connect all cables and wires to the indoor unit, starting with the power cable. Here you can open the maintenance cover, underneath is a cover for the power terminal. All wires are labeled which makes connecting very easy. The wiring on this unit is all set so now I reclose it. I lay the indoor unit on the floor so that I can lay all the cables out and line it up directly under the hole in the wall. Next, I roll out the copper lines and try to get them as straight as possible. Next I will connect the coolant lines to the inside unit.
#aircondition #split #acinstall
30 мар 2019
