Aleko Awning Motorized - Setting the Closed Limit 

Thanks for this video! Just installed my awning this weekend and agree with everyone else. Instructions are "OK" but not very clear with the open/close limit. I'd like to offer some additional tips to others: 1) I mounted my motor on the right. The close limit is still RED. The open limit is WHITE. 2) As someone else mentioned, connect the plastic hex tool to a variable speed drill because you will need rotate the screw a LOT. Make sure you use a low speed setting on your drill. You dont need a special bit. Just feed the plastic tool handle right into your drill. It should fit all 1/2" drills. 3) For setting the close limit: Open you awnding to about 2ft out. Adjust the RED screw with the drill. For me, I must have spun it at least 10seconds. On your remote, see if the awning will close. Eventually you'll notice that the awning doesn't close. That's when you know you've reached the close limit. Spin the screw a few times with the drill. Use the remote to extend the awning then try closing it. The close limit should be closer to the frame now since you've adjust the limit. Keep doing this until you get within one foot of the frame. Once you get really close to where you want the close limit to be, stop using the drill and just manual spin it with your hand a few more click until your desired position. The motor will move with each click. Test out the limit with the remote by extending then closing to make sure it hits your limit. 4) For setting the extend limit, it's pretty much the same instructions as the close limit, but use the WHITE screw. Extend about halfway, spin the white screw a few seconds with drill. Use the remote to extend more. If it does extend any more, then you know hit the limit. Use the drill to set the extend limit then use the remote to determine where the limit it set. Hope this helps!

Thanks bro. I couldn’t have set the limits without you help. I put the tool on my dewalt drill and found the limits easily. Just keep spinning counter clockwise until you feel the screw bumping over the last screw thread. Then un the motor and twist the tool to the desired limit. Cool!

I replaced the awning fabric and ran into the same problem. After trying all kinds of stuff I noticed the allen screws and thought, wonder what these do. Came right up to your video and everything lines up perfectly now! Thank you for posting this informative video!

Thanks so much! I was turning the limit switch a couple of times. It did nothing! I didn't realize the limit switch adjustment would actually move the roller manually. After watching your video, I now know what to look for when making the adjustment

“ THERE WAS NO CLEAR INSTRUCTIONS”. Boy that says it all right there!!😳. You just said more than the whole darned manual . You deserve a beer 🍺 Aleko deserves a kick in the family💎 😠. That comment of “ endless” and “120 turn until you EVENTUALLY FIND WHERE YOU ARE to start with. Thanks Bud ya saved the day🥳

Thanks for the video Sutter ridiculous that there isn’t better guidelines from the manufacturing have to turn in 100 times. One would think something doesn’t work.

Had a limit on extension, thank you so much this resolved it and made my day !

Thanks trimmed the end to get new looking fabric and needed to adjust to close all the way. THANKS

helped immensely,, Thank you. Yes instructions very poor for many things..

Thanks having the same problem. This will help

Thank you so much. I thought is was broken.

OUTSTANDING !!!!!!!!!!!!!!!!

THANK YOU!!!!!!!!!!!!!!!!

I have thy instructions included in the box,also the video aleko has for 8 minutes show how to adjust the limits

I very much appreciate this video. This product is one I could never recommend. The instructions are horrible. Bizarrely, even though my motor was mounted on same side as the one in this video, and the colours of the limit screws are the same and in the same order as this video, the functions of the two limit screws were reversed in mine! Given how many times you have to turn the limit screws before they do anything (which I only knew because of this video), it took me a long while to figure it out (why is it STILL not limited the retraction? Oh, now I just happen to find out it was limited the extend all this time!). Crazy. I got this only because the anchors were already in place from a previous owner and I didn't want to have to seek strata approval for new anchors. But I do not have high hopes for this product and I do not recommend it.

Thank you...

Thanks I was having same issue. Thought was doing something wrong.

Instructions are torture! I'll keep turning it. lol

Steven by any chance do you know if the opening limit can be done about 3 feet from full size? I bought a 12 x 10 , but I want it to just go out at 12 x 7 is that possible? Thanks

Thanks for the video, where did you get the long flexible allen driver for this ?

Where did you get the tool?

Many Thanks Steven! Instructions were poor as you stated.

are you unplugging the motor every time that you extend the awning and then plug it back to retract it to find the closed limit stop ?

Verified purchaser, verified assembler. It’s too late to turn back now. All the boxes are opened and parts scattered everywhere. The first comment I must make is this. Either all the retractable awning manufactures must also have pathetic assembly instructions. And RU-vid support videos made by the most incompetent composers. Or this Aleko company would have already been out of business. The printed instructions provided inside packages are disgusting. Images of parts on instructions do not match the parts provided in the box. Important steps are either omitted. Or they come along in the assembly process out of order. Causing one to disassemble to reassemble. There are parts in the box that are not even on the assembly paperwork. As far as the RU-vid videos recommended by the technical support. They too are still missing steps. The parts shown being assembles in these videos actually change from one step to the next. Possible different product revisions of the units over the years. But why then in the same assembly video. It’s like you are being shown how to change a transmission on a 1965 F150. But then you are suddenly being shown how to do the next step on a 1985 F150. I purchased a motorized unit. There were zero instructions in any of the boxes on how to assemble that part of the process. And the RU-vid video recommend by the technical support was one of those that changed parts being assembled along the way. It has you looking through all the parts provided tying to find these other parts. As they look like they would have worked better. Not sure which revision they were from. Not the one delivered to me. But more revisions are still definitely needed. How in the heck this happens is beyond me, I still managed to get the unit assembled in a day. And once one gets through it. It really pisses one off seeing how a set of clear and up to date instructions would made it a whole less frustration. And how it would have been so easy for the manufacturer to have provided that. It is like they want people to hire someone that has done it before. I pray to God it works now once I get it mounted on the house. And then lasts beyond the point where I forget how frustrating of an ordeal it was.

With Motor on the left I turned the White screw CW to raise the stop up. I guess all adjustments don't work the same. Way to confusing

What is “the tool”

What if it’s not rolling up