Applying Epoxy Resin to a Glittered Tumbler 

You just completely made my day!

Thank you. I highly recommend reading the entire data sheet for whatever chemical you are using. If it is not in the package, you can find them online at the manufacturers website.

Thank you! Have fun!

Thank you! Please be safe!!!

Thank you! Goal achieved! :)

Thank you! Welcome!

Well, aren't you sweet! Thank you!

Thank you. The turner definitely helps.

Violet Doodles Boutique how did you make the turners? That would be a great next video. 😊

Sorry, that is not in ours plans. I have plenty and they are very time consuming for our busy family. You can search other makers for tutorials on making them and tweak them for your needs.

@@VioletDoodlesBoutique awuick basic description wouldn't of killed u, smh

Sorry to disappoint. My turners are custom made with lots of specialty parts and have been through a few revisions. There is no quick description of them. Hope you have a great day!

Awesome! Thank you! I love hearing that!

You are so welcome!

Thank you very much!

Thank you!

How did it go?

Thank you!

Than you!

You're welcome!

Thanks! I try to be thorough without going too far.

Thanks!

Thanks

Thank you and you're welcome!

Thanks!

Thank you!!

Thank you very much!

It is!

Thank you

Thank you!

Thanks!

I believe those are just a yellow glitter and the rest is done with vinyl. You can probably find the cut file on Etsy.

Thank you. Be sure to research the appropriate safety gear. It really isn't hard but can be toxic.

Thank you! I have several videos that show different techniques. Here is the glitter swirl: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-XIRVCgL-9WY.html Thanks for watching!

Thank you! A very talented engineer executed it perfectly!

@@VioletDoodlesBoutique DO you know where I could buy a turner?

Check Etsy. There are several turner makers.

Thanks.

Thank you!

Hurry up USPS!

@@VioletDoodlesBoutique it arrived!!!!🤗🤗😍😍

WOO HOOO!

I don't think he really wants to make another one. I asked for two more... he's stalling. :)

Do you mind saying what the rubber black end pieces are and where they were found? As well as the metal pipes pieces? I’ve built a decent turner myself but I’m not thrilled with the football on the PVC. I just feel like as if it’s sturdy enough.

The black on the ends of the pipe are actually tesa tape. It is a soft tape meant for wiring. It was just what we had on hand. We used it to make the PVC fit a little tighter on the pipe but still easy to get it on and off. You can find it on amazon. The pipe is a stainless steel pipe that we bought and had cut down to our specs. He is an engineer and designs machines for a living. It is definitely sturdy and hardy.

You can but do it on hot and low flow. If you have a torch or even a BBQ lighter, you can also do that. Thanks for watching!! Good luck!

Lou Bascelli Well, it was custom made by my engineering husband. I just told him what I wanted and he went with it. It’s chain driven, has one motor meant for a 3D printer, and turns 5 at a time. I had an MDF body that I might paint some day.

It might still be bubbles, you can try a torch too but be careful not to burn it. I usually use paper towels but coffee filters work better.

Thank you. I move the tape about 1/8th inch each time.

I apply vinyl after a smooth coat of epoxy, usually after the second coat.

My husband made it.

I show that in the video. I just use a baby wipe.

It's a little different. For that one, I did the same technique for the teal and purple, both fine glitters. Then with the first coat of epoxy, I added the chunky, let it cure and recoated it.

You can do it! Here is my prep video. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-LAjpoMDMIUA.html

Every epoxy is different. You may need to let it spin longer. I have found my sweet spot between 20 and 60 minutes. Then to get the smooth line, I wipe it with a baby wipe.

You can hand turn but its a lot longer than 20 minutes. Search hand turnining. Minderella has a tutorial on how to do it. You can get smaller turners on Etsy, Amazon, and even Hobby Lobby now. The black no-name one from Hobby Lobby is around $30ish and I have 3 that I like. Stay away from the Spin It brand- junk junk junk.

Exactly the same for every coat. Yes, the glitter can move. If you are worried about it, you can use a clear spray sealer.

I use spray paint for a base. Yes, that is the basic process. These are not safe for the dishwasher.

Thank you. Yes, it is an investment. My husband made the cup turner for me based on my needs. I have outgrown it already.

@@VioletDoodlesBoutique nice husband too😆

Yeah, I kinda like him. ;)

What did you use for the motor?

I am not sure exactly. It is meant for a 3D printer.

I didn't record that one but it is a hot pink glitter (maybe Drive Thru Daiquiri from Mr. Nola's glitter on a white base). The design is all glossy and opal vinyl i cut on my Cameo.

This is the tutorial on how to apply epoxy. It is the same process for every coat.

I don't but it would be the same way. I have this video that shows epoxy over dill weed. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-CIHGvz4U6xo.html

I use the heat gun each time I apply epoxy. It helps pop bubbles and smooths the epoxy for an even layer.

After a smooth coat of epoxy. Usually on the second coat with some light sanding first. Then clean well and epoxy again.

I usually do mine overnight. If I am in a hurry and trying to load up turners as fast as I can, I will turn for 6 hours and them set it to the side. You have to be careful though, it will still be soft and can leave finger prints (ask me how I know, lol). If you do it too early, the epoxy can slowly run down and create a hump.

After your design is finished and completely dry, you will want to coat it with epoxy. Here's how: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-HDJhMsWh3zg.html

Epoxy is self-leveling. I'm sure it would work but you may need to do more layers to cover everything.

Check the descriptions of my videos. I try to list the supplies I use and each video has a few different things. This can be an expensive hobby and there is no one place I shop.

After cured, hand washing is fine. I have some that are a few years old and get used weekly.

@@VioletDoodlesBoutique Thank you so much for your reply!

No problem.

Thank you. If you want to use the cup to drink from, you will need to protect it and seal it with epoxy.

It depends on the size of the cup and if it is going on glitter or a smooth surface. I typically do multiple (4-5) cups at a time and make 60- 90 mls at a time.

Sorry, my husband makes them for me.

There are several n RU-vid from other makers. I do not have plans for this one.

That is a common issue. It could be due to several factors. If it is over a chunky glitter, spray seal it first and that will help. You can go over it again and it should be more evenly covered. Sand after two coats and wash well with Dawn. Then coat again. Good luck.

Yep, it will start to set up in about an hour, harden almost completely within 6 or 7 hours, and fully cured in 3-5 days.

You can spin by hand but you will need to dedicate several hours (6-7 hours) to turn it by hand. The heat gun helps pop bubbles and even out the epoxy. I don't always use the gun if I don't see the bubbles.

My husband made it and said he will not make them to purchase.

I have one motor that turns a chain. All of them turn together.

Those dimples could be from several factors: temp, amount of epoxy used, oils from handling, the glitter itself, bubbles... I don't warm mine except for the heat gun after applied but I do keep my room warm. Here are my steps: *prep cup- sand and wash with dawn *sometimes basecoat *glitter *seal glitter for chunky or complicated designs *epoxy 1 or 2 times *lightly sand and wash with dawn *decal *wash with dawn again- I never skip this step! *epoxy final coat *wait 3 days and clean cup well with (bare stainless with acetone) and then whole cup with dawn I hope this helps. Let me know! Good luck!

The rims, inside, and bottom of the cup that are still bare stainless steel. Those parts, I clean with acetone to make sure the paint, glitter etc are cleaned off well.

@@VioletDoodlesBoutique what do you deal the glitter with?

I seal the glitter with epoxy. Here is my epoxy video. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-HDJhMsWh3zg.html

between 20-60 mins

My husband made it. There are tutorials on youtube by other maker that show similar ones.

I haven't found a wholesaler for epoxy. I actually haven't looked for one. Ventilation and proper safety equipment is a must.

It is Neon Orange from Recollections. I list the supplies in the video descriptions for your reference.

My husband made my turner. Check Etsy for small businesses that make them. Michaels just started carrying a single. I will do a review on it soon. Amazon also has some.

I don't have a lot of the details. My husband made it for me. I have answered a few questions in the comments of this video if you want to scroll through. But I was pretty hands off. I just told him how I wanted it and he came through.

I am afraid the hair dryer would blow too hard and not have the heat it needs. Heat guns don't blow very forcefully and get a lot hotter. You can also use a mini torch. All of my vinyl is sealed under epoxy.

You can use a paint brush or foam brush but they would be single use and can incorporate bubbles. You can also use a silicone makeup spatula and apply it with that but I find those to be more work than just using my hands. The epoxy is self-leveling, so if you get it on the cup as even as you can it will settle and smooth out on its own.

If it's just a small spot, you can sand it smooth. If it's a patch of glitter that isn't coated, recoat before sanding.

Yes! I haven't done it personally but I have seen them. I have done UV color changing cups. So many possibilities! I am closed for custom orders until after the holidays but you can order by sending me a message through my socials or email angie@violetdoodlesboutique.com. Thank you!!

It depends on what you're doing. Two color ombres, I don't seal. When I do seal, I use a clear gloss spray.

My husband did.

Check Etsy. There are lots of turner sellers. Read the reviews and ask the seller questions to make sure it is what you are looking for.

I apply vinyl after a smooth coat of epoxy, usually after 1 or 2 coats.

These are all Hoggs. You can get them from The Stainless Depot Co wholesale or Hogg Outfitters retail. All of my supplies are listed in the description of my videos.

My husband made it. I have few details but is is all controlled with one motor. I think the motor is meant for a 3D printer.

@@VioletDoodlesBoutique ok tkx so much...your art is amazing

My husband made it for me. I have few details.

Amazon has them

You can hand turn if you have time and patience or buy a turner. This one from Amazon isn't bad (aff link) amzn.to/2VPIjWH If you want to try hand turning, Minderella has a tutorial on it. Search for her channel.

Thanks for the sub! You will want to hold off sanding until epoxy. I sand after the 2nd coat of epoxy. If you sand the glitter, you will end up sanding the color right off the flake.

I have done it on glass and stainless. It can be done on acrylic but I have not done it. If it can flex very much, the epoxy can crack or separate from the base and create problems.

Yes, I usually do them in the evening and let them go overnight.

Sand with a wet surface and wet sand paper. Here is how I prep my cups. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-LAjpoMDMIUA.html

Yes, you may have to do two coats of epoxy to have a smooth finish but that is the basic idea. If you are adding vinyl, do it after a smooth coat of epoxy and then seal it again.

Epoxy until smooth, apply vinyl, epoxy again.

Fisheyes are caused by debris or residue that hasn't been cleaned off.If you already have them, lightly sand your cup and wash it WELL with Dawn. Dry it with a coffee filter or microfiber towel and reepoxy. I use MP and epoxy to apply glitter. It depends on the technique I am working on.

All epoxy resin yellow over time. Some are faster than others.

Etsy has many turner sellers.

Cup turner, cup spinner, cuptisserie... You can find them on Amazon, Etsy, and videos that show how to make them on RU-vid.

Nothing will give you the shine and durability as epoxy.

I almost always do it overnight because of my schedule. If I am in a hurry and working throughout the day, I let mine spin at least 6 hours.

I only seal if it is an intricate design, more than two colors, or chunky glitter.