Arduino Uno (ATMEGA328P) on a breadboard Tutorial DIY project. Easy guide. 

Hey nice job! I finally got this easy to do memorized. My other standalone s were allot more complicated I didn't use the serial but rather the Ardunio UNO and removed the chip.

Siddharth and I were working on the DIY board for arduino uno and were not able to upload to the chip. On seeing Your video we saw that we had not connected the DTR to reset pin through a capacitor. After doing it the upload went on well.Please accept our sincere thanks for uploading this video to RU-vid which solved our uploading problem in our DIY Arduino board.

Thank you for this great video. It really helped me. Bravo.

Thank You Sir :) You realy helped me out on this one :)

Great job. Thank you for showing easy way to make it.

Thanks, great vid.. I found the best and easiest way to burn the bootloader to a blank chip is to use any Arduino board (even clones and counterfeit boards) in ISP mode. There's a sketch in the examples folder called ArduinoISP that does it all.

Cool, precise, educating videos here people!! [Αδερφέ είσαι ωραίος! Σε ευχαριστώ.]

Hey, great video. Thank you are your videos.

Thank you very much Sir for this simple informative video...

Thank you!

Thank you again for such a clear and detailed tutorial, The only problem I had was that it would not upload with the 100nf capacitor, I had to place a 10k resistor from pin 1 to 5v, tried other capacitors and different values but the same result; why do you think this is happening, again with thanks.

Εισαι Αρχοντας!!!!!

For everyone who cannot get it running because the device is not recognized: 1. You should pull up the reset with another resistor. 2nd.pins 20 and 22 need to be connected as well - they are GND and VSS. 3rd. You need some drivers for the FTDI. 4th. Make sure the chip is properly placed in the board - mine wasn't making a connection.

is the circuit is short proof nd it can able to communicate with serial devices like HC-05 bt module

Very useful…thanks!

Is it possible to work without the pF capacitors and the external 16Mhz? ie only with the built-in 8Mhz crystal? Thank you.

THANK YOU!!!!

How do we know what external components we need and how to wire them up for a specific AVR Microcontroller? I couldn't find a diagram with the crystal / capacitors in the ATmega328 datasheet, so how can we figure out how we should set it up with different microcontrollers?

i'm working on atmega328p project. i use fast pwm at the 16 bit timer. so i want to output 2 pwm at OCnA and OCnB. both of them have a same top value and same OCRnA and OCRnB. does anyone how i can toggle OCnA and then OCnB repeatedly

saludos. como seria el montaje del mega328p en protoboard para un servo.gracias. ya tengo la programación

allot of great information in this video thank you for sharing

Thank you this video was extremely helpful, i am new to arduinos. However I wanna know If I would be able to extend this project and add things like a display, and clock module directly to this schematic? Would this function the exact same way a regular arduino uno would?

You can post Multimeter mount photo to check the current consumption? In measuring realized that met minimum current 6,4mA

Aside from the power supply and all that, with this you can do everything as if you’re using the original board? I need to know :(

Thanks man !!!

hello i do exactly the same circuit with an atmega 328P from an arduino board with the blink led sketch on it... on the breadbord the led does not blink ... why??? the crystal 16Mhz and 22nF capacitors from arduino shop. i try 2 times with different breadfboard and 1 with soldering print. an idea please .

Thank you very much

Thankyou for sticker tip

do you need to use the microusb to serial component?

Είσαι μεγάλος. Μπράβο!

Awesome sir I'm subscribed😍

Arduino UNO R3 328: When you have programmed with usb afterwards you want to avoid usb completely! But I have to plug in usb & program again what should I do to keep it saved forever?

hello ..do you have a vid where you show how to upload the bootloader to that mcu?... awesome

Excellent Tutor....

I've already ordered the atmega , which comes with a socket and crystal. I have to order the caps seperatley, but those are cheap.

I have made everything correct, but when i supply my circuit the led doesn't blinking, my atmega328p is from my original arduino board, any thoughts?

Very nice tutorial

I tried copy your arduino so my led on digital 13 is off no blink.Can you help me please???

Thanks Sir . I want to learn .

Hi, I was making your project when I came across a error that the Usb was not responding and I was using a CP2102 USB-TTL board 2.0 pls help me fast, Thank you

what does this code mean ( w10647Asz113 ) ???? i read it on a pcb board under the ATMEGA328P-PU

Thanks !

Hello can I use 47 uf capacitor

Could you please supply a PCB Layout? Awesome!

Very interesting. Exactly what I want to do. Is the serial monitor available here? Thanks.

The crystal is missing from the parts list, to suit the 22pf capacitors the crystal needs to be 16mhz with a 10pf load capacitance. You can use a 20pf crystal but the 2 capacitors need to be 36pf.

Please can you tell how to measure power consumption @7:00 ? I cant see the connections to multimeter.

if i did not put the 100nf at pin 1 does it okay???

Super video bro 🎉

Thanks allot 😊

Is it possible to trigger atmega 328p with 3.3V ?

Nice to learn

Tank you.

sir,what is the resistor value that you have used

how to add magnet sensor in this project ? or PIR sensor?

have you tried to burn arduino bootloader in to an Atmega8A-PU?

Do you need to upload the firmware fisrst?

please make tutorial for bootloading atmega328 to use internal 8Mhz and explain bod

Will PWM and analogs also work?? There is a large capacitor on the Arduino, it is not here. It would be nice to do your project. Bravo

At 7:33 it says that Arduino Pro Mini takes 3mA when sleeping, but according my measurements it only takes 0.14mA. Maybe you confused with Pro Micro (the one with USB port)? When the power LED is removed from Pro Mini, it takes only 0.05mA, so similar to naked ATMega328P on a breadboard. However, once it wakes up, it only takes around 4mA, and that is 10 times less than what your multimeter is showing. I guess it's because the microcontroller on Pro Mini is so small, so it requires less power? I don't know. But it seems to me that using Pro Mini 3.3V with power LED removed is actually more power efficient than what you are showing in this video. Maybe you can check my numbers?

Sir by which software you load the program

Thank you sir very good video can you tell please what would be pin number for 5v in Arduino board

Thx sir.

wow, thats amazing, by far the best video I've seen so far,but I have one question: I have a small project in mind but unfortunately I can not use a full Arduino due to the size where it will be. I could for example fit Atmega328 on an IC socket and weld everything I needed him? so I could to minimize the maximum Arduino size for my project.

Thanks for the tutorial! Is it possible to just download the sketch when the chip is still on the arduino and then just take it off and put it on the bread board for your project? --And then just stick a new chip back on the arduino so youc ould do it again for multiple projects? thank you

Thats weird... my multimeter says my barebones arduino with sleep library uses only 6.7uA, whichi is 0.0067mA, yours was 0.06-0.07, which is 10 times more than my multimeter says.. thats weird

Can I use atmega2560 just like this?

Super sir

how do I connect Ch340 uab to ttl converter?

hi is there a way to change the value of a Variable in a Void Loop, because I try in the Void Loop I try if (X==0){int X = 1;} but it did not change the value of X even the condition is true it remain X=0.

Whats the point of crystal and capacitor? Can you someone explain to me? Would the chip work without them?

How can I program my Atmega328p without an Arduino board? I am looking for a serial diy programmer. The atmega already has the arduino bootloader

What is the value of the resistor anyways? i think it's not mentioned in this video.

Hello, Great video but I have a couple questions. First what size resistor is used for the project? Next I thought the atmega328 had to use between 3.3 and 5.5v but you appear to use 4 batteries and at 1.5v each is 6v total. So am I wrong or are you using rechargeable batteries? Thanks in advance Gren

A bare-bare bone ATmega328 you could programm with an ArduinoISP

Hi. I have a UNO with a rx and other tx modules that needs 9V. How could I supply 9V in this breadboard ATMEGA??

how to load bootloader on the atmega328

Oh this is so cool. I see you're using a low power library. I've got all the parts to make my own Arduino except for the crystals I'm just waiting for them. I like the stickers you made that's handy! I'm going to print them up! :-) Question, just out of curiosity, the Mastech MS8268 can test DC current without the cables connected? It doesn't say that in the manual.

Dear Greek , I am Greek too. I tried so many times over a week now and I cannot make happen. I really need help please. Problem uploading to board.and I have used exactly the same boards and FDTI board. Can you help me please? Kind regards Demetris

Loved the video but could use some help if possible. Trouble uploading. Am using an ATMEGA328P-PU chip with bootloader. My usb adapter is 5V 3.3V FT232RL USB to Serial Adapter Download Cable module for Arduino. Re code, couldn't find a library called LowPower as shown in the code. I found one from github called Low-Power-master and loaded that into the IDE but I left the line of code #include "LowPower.h" the same. Compiles ok but if I change it to #include "Low-Power-master" I get an error. Confirmed "Low-Power-master" was loaded into the IDE library.When I plug the circuit into PC via USB I get the following under tools:Board: "Arduino Nano"Processor: "ATmega328"Port: "Com8"I verified via the Device Manager Com8 shows up correctly.After it compiles, the "uploading" message stays on for about a minute then I get the "Problem uploading to board" message. I tried searching online for the same issue but having trouble finding something that helps. I really would like to find a solution as I'm working on a real project and would like to use a low power setup if possible.All components come from a kit.I appreciate you help. Thanks.

The main reason is learning is fun....

It doesn't upload the code for me although I do everything exactly like in the video. It tells me that it cannot open the device, cannot find the specified file.

Is there a video for the actual programming?

Can we build something similar using ATTiny2313??

nice

So where is the link for the sticker? I want to print some. Thanks.

You can only program this once if you dont burn a bootloader? If you just upload any sketch it will work, but you wont be able to upload any other sketch :/

What board did you select in Arduino IDE?

the funny thing is that you didn't need to buy that usb converter, just plug the atmega328p to a socket of another Arduino board and program it temporarily

Which value of the resistor do you used with LED

Easy

I have a Arduino Uno. Is it possible to upload my Sketch to the Uno, then remove the Atmega328 from the Uno and connect it to the breadboard like you did? Is this a possible way to install my sketches?

What is the URL for the ATMEGA sticker (w/ pin labels)?

hi can you make a good and well defined so we can use and learn it ................................please

How do you program the chip?

if run like the coding, 8 sec sleep (0.06mA), and 1 sec on (36mA), so the total work time is 9 sec, the battery is 2400 mAh, and the calculate is : = {2400 ÷ (((8 x 0.06) ÷ 9) + ((1 x 36) ÷ 9)))} = {2400 ÷ ((0.48 ÷ 9) + (36 ÷ 9))} = 2400 ÷ (0.0534 + 4) = 2400 ÷ 4.0534 = 592 hours. 592 ÷ 24 = 24.6 Days. CMIIW

nice video!!! are you from greece??

Sir Can you help me Im high school student I really like electronic . .ive a problem I have a color sensor i want to connect this to microcontroller without wiring (wireless) so how can i connect? Plz help sir

Which resistor you used in this

why my arduino port did not detect ???