Assembling the PwnCNC Dust Boot v10

Подписаться 3,5 тыс.

Просмотров 5 тыс.

50% 1

In this video, we'll be assembling the PwnCNC Dust Boot v10. This dust boot is a great addition to your CNC machine and can be used to remove dust and other debris during the cutting operation.
Be sure to check out this assembly video! We'll walk you through the steps needed to assemble the PwnCNC Dust Boot v10!

Опубликовано:

9 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@eldonhinck1487 Год назад

Awesome, thank you so very much. Helps us video learners so very much. I also didn't realize there are other extension Mag rings available for the use of longer bits. As you know, this CNC stuff is totally new to me, and any and all help you and your videos have given is truly appreciated. You and your company are truly amazing.

@PwnCNC Год назад

Now that we're in the warehouse.. and I have more regular quiet time... I can finally start producing more videos. They're fun to do and so helpful in explaining sometimes complicated CNC topics.

@skipchang 8 месяцев назад

Daniel, great video and very timely. Just purchased the water cooled PwnCNC spindle and v10 dust boot for my Onefinity Journeyman with Z-20 heavy duty Z slider for non-elite machine (and no stiffy rail). After watching your video, I was able to find the hose clamp that clamps onto the spindle for the front. However, I was confused on the which options to pick for the rear 90 degree hose clamp you had on your video that will work with the non-elite machine stepper motor. Thanks for your help.

@garagehobbies Месяц назад

I haven't seen any videos on what it is like to change bits. I just ordered one but wonder about that.

@threegreendown414 Год назад

Great video. I have the V10 dust boot for the 4" hose. Are there hose clamps for the 4" hose like you installed for the 2" toward the end of the video? My hose is flying all over the place without something to keep it in place. I am amazed at how creative you are to make all of these devices. Keep it up.

@PwnCNC Год назад

Definitely… there’s a 4” attachment in the options: pwncnc.com/products/ultimate-hose-clamp

@chrispelletier3661 Год назад

Hay Danial, thanks for the great video. Could you do one on the V9 in action on the elite… Thanks!

@PwnCNC Год назад

Absolutely. I’ll get it prepared asap and recorded. I’ve been wanting to do another 3D carve with the new Cody bits I’ve picked up recently. ;-)

@johnjahner3389 5 месяцев назад

What are the size of the magnets and the short and long screws? Thank You

@marksplayground 4 месяца назад

Where do I get the vacuum hose clamps?? I need them for a 4" vacuum hose.

@PwnCNC 4 месяца назад

pwncnc.com/products/ultimate-hose-clamp

@ShaunSchmidt-xb9fy 2 месяца назад

Any ideas how a dust boot would work with narrow but deep cuts from 5" to 6" deep?

@PwnCNC 2 месяца назад

The deepness of the cut is definitely the difficulty for any of these style boots which are abundant on the market. The boot's body will hit narrow/deep walls making it almost impossible to utilize this type of boot. Narrow but very deep (5-6in) presents a whole lot of design challenges and will be very difficult to setup anything existing boot design. If it were me, I'd setup air spraying at the bit and helping keep the chips away from the cutter, as well as an enclosure or some other machine-size containment for the dust and clean-up afterwards.

@SailingCatamaranElement 2 месяца назад

@@PwnCNC Yes, so you see my issue....for now because the pocket cut is limited in size, the solution is to hold a shop vac end near the pocket while cutting...an enclosure in my particular case will not work...when I have completed my proof of concept case for the work I am doing, will post a video...

@wayahedia9989 2 месяца назад

Do you sell the parts to convert a 2.5 inch version to a 4 inch version?

@PwnCNC 2 месяца назад

We have designed a few options, can you describe which 4" product you're wanting to change to 2.5"? there are a few and different adapters work better for each situation.

@wayahedia9989 2 месяца назад

@@PwnCNC I ordered the 2.5 inch dust port for the spindle I have on the way. Mainly to accommodate existing connections. But the HF dust system I have is a bit weak and I was thinking I may have to go to 4" at some point. I ordered the V10. Can't wait for it all to get here! I am slugging through with an original X-carve!