Automotive Relays For Dummies | 85 86 87 87a 30 | How To Wire A Relay | 5 Pin vs 4 Pin | Look Inside 

Thanks for the tutorial Ryan. I'm 67 and never really took the time to study and understand relays, in detail until your video.

Thank you very much for this video. I have been connecting driving lights for my cars many years and i have been using relays. But now i have so many ideas for for other applications!!!

Thank you for sharing your knowledge 👌🙏🙌🫵🫶❤ I love the way you explain each section . Blessing

Much better explanation than most, Kewl.

So glad you did this. Know a little, but always great to gain knowledge. Thanks

Thank you for a very beautiful and clear explanation...you are wonderful teacher ❤️ 💖 💕 GOD BLESS YOU

Was after the schematic, nice to see it early in the presentation

Very informative and helpful video. Thanks for sharing, Ryan.

Lol "I love relays"... Words i have uttered under my breath, because I don't want people to think I'm weird 😅

I really enjoyed and learn a few things along the way with your work here. But I would really like your thoughts about the silver wolf build, likes and dislikes especially. Thanks again for your work here.

Great job thanks for the info.

I enjoy the relay info and was considering installing one on my golf cart so my 48v->12v converter doesn't drain the battery (like you mentioned). But I turn my 48v 95ah lithium battery off when not using the cart. Not sure I would get any benefit from the relay in this case, but will consider for possible future installations.

Great explanation sir!

Thank you.

You might want to " clamp " the DC relay coil with a diode hooked inverse parralel on the coil. A 1n4004 should be good in my opinion

I like this video.

I have a side-by-side CanAm UTV with a 12V battery. There is a power distribution terminal under the dash that will energize when the ignition is on (there's a ground lug near by as well). Also, there are color coded wires passing through the firewall from this location directly to where the battery is located. I wish to provide power to my stereo, light bar, whip lights, back lights and rock lights via this power distribution terminal using rocker switches. My question is this...will this be too much for this terminal, and should I use an individual 30a or 40a relay for each device? Thanks in advance for your advice!!

Putting a radio in my 12v gas golf do I want a relay or solenoid wired to the ignition on wire

Looking forward to more information about TEMGOT batteries. I want to buy a 300ah heating battery from this brand. Is the battery currently working abnormally? How do the heating function and app function work?

Good information and well explained. Question though. I am going to use a relay on my motorcycle to control the front mounted passing lights. I am planning to use a relay in the normally closed position to power them all the time the switch is on.. But plan to use the high beam power to activate the relay to cut off the passing lights when the high beams are on. But i can not figure out if I would need to wire it in line with the power to the high beams or if just tapping the power side will work and grounding it to complete the circuit. Any advice would be helpful. Thanks.

good evening i have a question for you i have a 12v air compressor that we installed a pressure switch in was working fine for a long time went t use it today and it wouldnt turn on there is a breaker a on off switch and relay alongside the pressure how do you tell if the relay or the pressure switch is bad switch

RRL. Relay Relay logic.

Awesome

Hi Can I power the relay Pin 30 and patch 85 from the same 12v supply without damaging any switch gear?

hello , i want to wire ambient lights on my car. i want when my car is unlocked the ambient light turns on. also i want the ambient light to be on when i driving . If i put a 5 pin relay with one pin trigered from acc so i can have lights on when driving and the other pin from the ceiling light to open the ambient lights when i unlock . Do u think that it will work?

Does anyone know how to remove the wires from the relay harness ? I would like to use my own color code layout that I have created for myself, and I am used to using. I find it very frustrating to see a colored wire change to a different color wire. I could also buy a bunch of colored heat shrink and cover the wire with my own color code. That seems like a lot of money and the wire becomes stiff and does not bend as easily. I would like to find some type of pin tool that will allow me to remove the metal connector that is inside the relay harness. I can then either reinstall the connector and its wire to a different position on the harness. If the harness does not come with the wire colors that I am used to using then I can remove a female spade connector from its plastic cover and attach it to a wire that has the color that I am used to using, and then install the new spade connector and wire into the relay harness.

Proagation delay of about 20 ms.

Hi! Can I run 24 volts from 30 to 87 and 12 volts on the trigger (85/86) switch? I'm planning to install a 24v airhorn in my car and I just bought a 24V boost up converter.

Please ditch the annoying background music.

Form C contacts, spdt.

holds the relay with the 666 hand sign... blah blah smart battery with lcd-junk! came here for info on relays not this info on this junk battery! video starts at 2:17