B&G Tech Tip | Pairing the B&G WS320 wind sensor

Подписаться 7 тыс.

Просмотров 11 тыс.

50% 1

Tech Tip - How to pair a B&G WS320 Wind Sensor to a bluetooth base unit and your network.
Please comment if you have any questions or suggestions!
There's a lot more great B&G content out there. Follow our channels to stay updated with all the latest B&G news and stories.
Go to the Website for more information: www.bandg.com/
Subscribe to our RU-vid Channel: / bandgsailing
Like us on Facebook: / bandgsailing
Follow us on Instagram: / bandgsailing
Follow us on Linkedin: / bandgsailing
#bandg #trustedtoperform

Опубликовано:

19 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 13

@johnbarratt983 2 года назад

Helped me pair my new wind sensor.

@Kruncher55 Год назад

Haven't been on the boat much this year, but went sailing yesterday and no wind data. Sensor is 1 year old, San Diego, plenty of sun. Said Power [OFF], then in the device list, 0%. Did I just loose the BT signal? Will I have to do this everytime?

@thomasandco1831 2 года назад

Hi I previously paired my WS320 wind sensor (and had the data flowing) and then I stored it away for a while with battery connected, when I have come to fit it there is no longer data, and I’ve subsequently tried to re-pair it (for a few hours) but to no avail. Not sure if I need to ‘reset’ or something?

@soulsailinghippie357 11 месяцев назад

If i disconnect my boat batteries and lose power to my NEMA 2000 backbone will I have to climb up to bring the unit down to pair it again?

@daveroberts1 6 месяцев назад

I'm trying to pair by following these instructions. The system shows the 320 device. It paired when new but over winter 22/23 the data stopped. Battery now replaced and shows 325mv but will not pair again. Any thoughts?

@i1uvpreppyxo887 2 года назад

So every time a battery needs replacing the wind sensor has to be brought down to deck level? Apart from that scenario are there other ways rthe pairing can be lost because having to bring the vane down from the mast in that case would be a real pain.

@BandG 2 года назад

If the wind sensor is exposed to sun, the battery should last for more than 5 years since it is being recharged daily. If pairing is lost it should be due to other reasons like poor coverage between the bluetooth antenna and the wind sensor or interference from other Bluetooth devices.

@chrismaroud8484 Год назад

Today, my WS320 wind data stopped.coming through. I tried restarting the nmea network, reconnect cables etc to no avail. I have installed the system (new) only a couple of months ago. Is there anything I can do other than crane into the mast to get the wind sensor to reconnect? What if this happens again in a few months?

@BandG Год назад

Your NMEA2000 network is still working, correct? Do you see the WS320 interfence in the N2K device ilst? Please send us a message via FB with serial number and contact details.

@unreliablewitness5047 Год назад

Hello, I’m having trouble getting my wind sensor to pair Following the steps you show. But no joy

@ignacioloureiro9279 7 месяцев назад

Hello which is the oficial FB page for B&G I am having the issue@@BandG

@Zippy0George0Bungle Год назад

Is this unit compatible with a Garmin MFD and can it be configured through a Garmin unit, or does it only work with B&G MFD’s? Thanks.

@BandG Год назад

There are no special procedures to be done via software, so the main data will be shown. Maybe you won't see the status of the battery and the pairing signal if it is good or not but AWA and AWS will be read.